PDA

View Full Version : SeaDek for 2017 X10


dklock
03-28-2017, 03:41 PM
Hello all ... new to team talk. I purchased a 2017 MC X10 late last season (located in NH). I am interested in installing the SeaDek product throughout. Has anyone done this already for this same year and model? Looking for some template advice or if anyone has this template created already? I am trying to avoid duplicating effort. SeaDek has just sent me the 2015 X10 template. Not sure if the dimensions are the same ... boat is still in storage.

And I apologize in advance if this has already been covered ... I looked but did not see anything posted.

lashburn1
03-28-2017, 03:42 PM
I believe MooseHead did it on his X-10
SC-Wake has the template on file for X-10

dklock
03-28-2017, 04:02 PM
thanks ... i will reach out

homer12
03-28-2017, 04:23 PM
Here's what I recommend if you are going ahead with it. I worked with SC Wake on my Nautique and they were very helpful. Get Dry Fit templates from them for the same cost as a blank clear plastic template. Then you cut and lay them out and mark any changes you need. If the 2015 X-10 is very similar to yours, it's a good place to start so you don't have to reinvent the wheel entirely but still ensure a custom fit.

dklock
03-28-2017, 06:18 PM
@homer12 ... thanks for the SC Wake reference. First I've heard of them (new to the wake boat scene ... sort of!) ... I will definitely give them a shout!

lashburn1
03-28-2017, 07:30 PM
@homer12 ... thanks for the SC Wake reference. First I've heard of them (new to the wake boat scene ... sort of!) ... I will definitely give them a shout!

They are a Sea Dek outfitter with better build time and customer service for individuals l buyers

ryancassidy
03-28-2017, 07:44 PM
Not to throw more options at you.....

but check out https://www.aquamarinedeck.com/ They did the gunnels on my 2017x10 and the local MC dealer uses them exclusively.

HTH's.

dklock
03-28-2017, 07:44 PM
yes ... that's what appeals to me more so than my local dealer

moosehead
03-28-2017, 08:42 PM
Dk, SC Wake has my '15 X10 template. See this thread: http://www.mastercraft.com/teamtalk/showthread.php?t=73389

Note there are a few imperfections that need cleaned up IMO as follows: (1) piece to right of helm seat has a corner that needs straightened, (2) corner just below observer seat needs cleaned up, (3) port side rear piece in front of rear seat has a line that is crooked or too thin at the outside edge at the center of the floor, (4) small corner at the rear pad behind the convertible rear seat needs cleaned up.

Sorry as my boat is in storage and I cannot give you better descriptions. What I mean by cleaned up is obvious lines, corners, or outside edges that are normally caught by the CAD system and straigntened need some attention here. Hope that makes sense.

Other than the above SC Wake is tremendous to deal with and I'll always have SeaDek Fauxteak in a boat's main cabin. Cheers.

moosehead
03-28-2017, 08:46 PM
Tried to circle the areas from my template that need the touch ups below.

https://uploads.tapatalk-cdn.com/20170329/3f6b2ec030b138ab7dc860658c7b3e9a.jpg


Sent from my iPad using Tapatalk

wheeler
03-29-2017, 07:48 AM
SC Wake did my X2 and my Buddies X2, couldn't be happier, great service.
Call 812-637-0262 and ask for Eric Sacksteder.
[email protected]
www.scwake.com

dklock
03-29-2017, 08:13 AM
thank you very much for the response and the detail!

dklock
03-29-2017, 08:23 AM
thanks again Moosehead ... my boat is still in storage so flying blind a bit ... regarding existing snaps ... how did you address the holes left after the snaps were removed?