header |
|
#1131
12-17-2011, 04:59 PM
|
||||
|
||||
|
Ok deck/hull joint restored and rub rail re-installed.... found a thread here that the factory guys can install rub rail in four minutes...took me an hour...not bad for an amateur... The OCD is getting the best of me...
 added the before when all the rivets were taken out...that took way longer...and really boring...
__________________
 ...A bad day water skiing still beats a good day at work...1995 Pro Star 205....
|
|
#1132
12-17-2011, 05:26 PM
|
||||
|
||||
|
Looking good...
__________________
"Hey baby want to make fourteen dollars the hard way?"--Rondhey Dangerfeild-Caddy Shack. "Was it over when the German's bombed pearl harbor ?" ---Animal house
|
|
#1133
12-17-2011, 06:41 PM
|
||||
|
||||
|
Last weekend I removed the engine cover and stripped the old foam and adhesive. Today I layed out my templates for the new foam. Now I just have to cut the foam and install this afternoon or tomorrow.
|
|
#1134
12-17-2011, 06:45 PM
|
||||
|
||||
|
While I have it apart I am going to replace all the exhaust hoses. I measured and it looks like I need just over 4 feet for each side from the silent master to the transom and 6" for the exhaust riser to the silent master on each side. I will buy the replacement bolts and riser gaskets while I'm ordering from skidim.
|
|
#1135
12-17-2011, 06:47 PM
|
||||
|
||||
|
Quote:
__________________
...A bad day water skiing still beats a good day at work...1995 Pro Star 205....
|
|
#1136
12-17-2011, 09:09 PM
|
||||
|
||||
|
I bought the 1" grey foam from McMaster not the metal covered. You can see it in the last picture the 3 templates are layed out on it.
As for cleaning, it was a pain I used a scraper to scrape it off on all the flat sections then goof off for the corners and curves, total it probably took about 3 hours to clean it maybe less. Removed and cleaned in 1 nap by my son and an hour or so after he went to bed.
|
|
#1137
12-17-2011, 09:19 PM
|
||||
|
||||
|
goof off - ack..hate the way that stuff smells.... nice job can't wait to see the finished project.
__________________
...A bad day water skiing still beats a good day at work...1995 Pro Star 205....
|
|
#1138
12-17-2011, 09:28 PM
|
|||
|
|||
|
Quote:
__________________
93 190 . Hypocrites, boot lickers, and crybabies…the world is full of them…. just look around - near-by . Duraflap / Kaydenco aren't worth a hoot Hose picture (internal) http://www.mastercraft.com/teamtalk/...68&postcount=8  Quote:
|
|
#1139
12-17-2011, 09:39 PM
|
||||
|
||||
|
Quote:
__________________
...A bad day water skiing still beats a good day at work...1995 Pro Star 205....
|
|
#1140
12-17-2011, 10:01 PM
|
|||
|
|||
|
Quote:
To me, it smells identical.... I'll have to go to the MSDS now.. .
__________________
93 190 . Hypocrites, boot lickers, and crybabies…the world is full of them…. just look around - near-by . Duraflap / Kaydenco aren't worth a hoot Hose picture (internal) http://www.mastercraft.com/teamtalk/...68&postcount=8 Quote:
|
 |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
