Go Back   TeamTalk > Maintenance Tips, How-tos and Refurbishing Topics > Restorations and Refurbishments

Reply
 
Thread Tools Display Modes
  #1  
Old 10-24-2013, 11:26 PM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
1991 Mastercraft Prostar 190 Restoration

Hey all. Long time reader first time poster! I have gained so much knowledge from these forums that I knew when I started my project I had to document it for others to enjoy.

So, I bought a 91 Prostar 190 powerslot this fall for 7k. I did my best based on knowledge I gained from here and from my previous boat purchases but still held my breath while my local mastercraft dealer checked out the boat. They noted it leaked from the exhaust outlet ports and had a miss in the engine but compression was within 2lbs of perfect on all cyls. I decided that i would have the carb rebuilt and the points replaced and would purchase an ACME three blade this winter. I had a craigslist person help me winterize the boat and this is where my restoration begins. I am stripping decals, wet sanding, stripping the interior and basically making it look the best I can on a busch light budget as someone else had said. I am going to try and figure out how to post pictures and I will add them below. Thanks for looking.
Reply With Quote
  #2  
Old 10-24-2013, 11:50 PM
Jeffer's Avatar
Jeffer Jeffer is offline
TT Enthusiast
 
Join Date: Feb 2010
Boat: 1996 ProStar 190
Location: S.CA.
Posts: 155
Yep, you already know what we all want....PICTURES!
__________________
Jeffer

1996 Prostar 190, LT1

"5 out of 4 people have a problem with statistics..."
Reply With Quote
  #3  
Old 10-25-2013, 12:34 AM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
pictures first try
Attached Images
     
Reply With Quote
  #4  
Old 10-25-2013, 01:51 AM
scott023's Avatar
scott023 scott023 is online now
MC Master Poster
 
Join Date: Sep 2008
Boat: 2008 X45 Switch L18
Location: Canada
Posts: 11,872
Your wet sanding well make that boat pop back to life. Looking forward to progress pics.
Reply With Quote
  #5  
Old 10-25-2013, 11:17 AM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
trying out uploading from my phone
Attached Images
  
Reply With Quote
  #6  
Old 10-25-2013, 11:32 AM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
let the work being! pealed decals with heat gun, just got them warm, didn't want to mess up the fiberglass somehow with too much heat... used thick piece of plastic with sharp edge mostly, occasionally they would peak a bit, heat helped for sure. decal removal is the worst no matter what. used 600 grit wetdry sandpaper with car wash soap in the water. sanded with a hard rubber sanding block. results were better than i could have imagined.
Attached Images
    
Reply With Quote
  #7  
Old 10-25-2013, 11:47 AM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
here is sanding, not sure if pictures are the same quality through my phone I'll upload more end of the weekend hopefully
Attached Images
      
Reply With Quote
  #8  
Old 10-25-2013, 11:53 AM
Chrismath88 Chrismath88 is offline
TT Enthusiast
 
Join Date: Aug 2013
Boat: 91 Mastercraft Prostar
Location: northeast
Posts: 100
notice the bucket of blue gel coat blood in the last picture. I just ran a buffer over that section to test results, looks great.. just got pad for drill at autozone only 8 bucks, should help with tight spots, can't seem to get guides off trailer... working around them currently.
Reply With Quote
  #9  
Old 10-25-2013, 12:05 PM
thatsmrmastercraft's Avatar
thatsmrmastercraft thatsmrmastercraft is online now
MC Master Poster
 
Join Date: Sep 2008
Boat: 1977 Stars & Stripes
Location: St. Paul, MN
Posts: 15,164
Great progress.
__________________
Peter

SPECIAL PRICE
ST205/75R15 KENDA LOADSTAR ON 15X5 WHITE SPOKE WHEEL, BALANCED & DELIVERED - $125 EACH


Tandem Axle Packages Starting at $569 - 4 Aluminum wheels, 4 ST205/75R14 tires, mount & balance.
Single Axle Package Starting at $319 - 2 Aluminum wheels, 2 ST205/75R14 tires, mount & balance.

CARBURETOR REBUILDING - $125 + PARTS
LED lights, Hubs, Spare Tire Carriers, Chrome & Powder Coated Lug Nuts

PM or email me tiresplease@gmail.com
*** FREE DELIVERY ON ALL ORDERS ***
Reply With Quote
  #10  
Old 10-25-2013, 01:37 PM
cesarcis cesarcis is offline
TT Newbie
 
Join Date: Sep 2013
Boat: 97 MC 205
Location: West coast
Posts: 19
cant wait to see the final pictures. Are you going to add the red stripe back?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -4. The time now is 05:12 PM.