Go Back   TeamTalk > Maintenance Tips, How-tos and Refurbishing Topics > Trailers

Thread Tools Display Modes
Old 08-24-2013, 10:03 PM
andersonmc andersonmc is offline
TT Enthusiast
Join Date: May 2013
Boat: 2001 X star
Location: Northwest
Posts: 255
Getting ready to paint trailer

So I'm getting ready to paint my trailer this fall. I'm going to leave my boat on the trailer since I don't have the option to borrow a trailer. My queston is I don't want to spray my boat and I've read in the past people using a roller or brush. What paint would allow me to use either method? I don't want brush marks and still looking for a nice gloss. I know shooting it would give me a better finish but I'm going to wait a couple years before I do that. This is more of a get me by paint job till then.
Reply With Quote
Old 08-24-2013, 11:18 PM
FrankSchwab FrankSchwab is offline
MC Devotee
Join Date: Aug 2004
Boat: 1998 Maristar 200VRS
Location: Phoenix, AZ
Posts: 1,850
Just a thought - get a big-*ss tarp, and put it over the trailer before you load the boat the last time this season. Pull it up around the boat, and you won't have to worry about overspray.

Alternatively, leave the boat in the water for a couple of weeks before you pull it out the last time. Leave all the marine growth on the hull - once again, you won't need to worry about overspray because it'll all come off when you scrub the gunk off.

Other than that, I don't have any great suggestions. I almost did mine this summer; was just going to rattle-can it.
1998 Maristar 200VRS
Reply With Quote
Old 08-25-2013, 11:23 AM
Retoxtony's Avatar
Retoxtony Retoxtony is offline
TT Enthusiast
Join Date: Aug 2011
Boat: 2007 Tige RZ2, previously 99 MC205
Location: Canada
Posts: 201
I'm planning on painting my trailer over the winter, unless my boat happens to sell before then (i doubt it will). I have some rock chips that drive me nuts. My plan is to use plastic sheeting and tape off anything i dont want paint on. It'll require me to do some crawling around but i don't think it should be bad. I was planning on trying using spray paint and see how it comes out. I've seen a few redneck paint jobs on vehicles over the years that i never would have guessed were spraypaint, so i know its possible to do a good job. I can always sand and repaint if it turns out like crap.

I'm interested to see or hear what others have done and how it turned out.
Reply With Quote
Old 08-25-2013, 04:21 PM
NWMike's Avatar
NWMike NWMike is offline
TT Regular
Join Date: May 2013
Boat: 1993 Mastercraft Prostar 190, 285 hp HO, 1:1
Location: Northwest
Posts: 74
Get a roll of thin plastic from the paint dept. of the big box store and a roll of tape. I sprayed mine with a spray gun. Since you're going to roll it or spray can it you wouldn't need much. If you do have any rust chips I would get a small bottle of rust neutralizer like a Rust Mort. Find a local body shop supply store for an etching primer to cover any bare metal once it's sanded and treated for rust (if any). Sand it down with some 180 then lastly about 400 grit, especially along the front rails where rocks get kicked up. Being it's a trailer and not a car, I go for a lower grit instead of 600 for more bite and less chance of chipping. Most of the spray can paint you purchase is either lacquer or uncatalyzed enamel. They now have paint cans with a catalyzer inside that can be activated. This will last and shine much longer than regular enamel paint cans. Have fun with it. Remember, if you do use catalyzed paint, you must wear a respirator. Can't hurt on the other paints either.
Attached Images
Reply With Quote

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

All times are GMT -4. The time now is 09:20 AM.