Go Back   TeamTalk > Maintenance Tips, How-tos and Refurbishing Topics > Engine / Drive Train

Reply
 
Thread Tools Display Modes
  #61  
Old 04-26-2013, 06:09 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place pressure plate springs and greased dowel pins.
Attached Images
    
Reply With Quote
  #62  
Old 04-26-2013, 06:14 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place your new reverse clutch plate assembly 90 and 91. Bronze goes in first, then steel, then bronze again (no picture of last plate).
Attached Images
  

Last edited by Wouter; 04-26-2013 at 09:22 AM.
Reply With Quote
  #63  
Old 04-26-2013, 06:20 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Next comes reverse clutch plate 92. Align plate half moons with dowel pins so that springs correspond with clutch plate holes. The plate should drop and sit almost flush with case.
Attached Images
  
Reply With Quote
  #64  
Old 04-26-2013, 06:29 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place gasket 97.
Place sealing ring 96 (I had forgotten this, that's why you still see it next to the blue screwdriver at bottom right of next pictures but you should place it now)
Attached Images
 

Last edited by Wouter; 04-26-2013 at 09:23 AM.
Reply With Quote
  #65  
Old 04-26-2013, 06:32 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
place forward and reverse adapter 99. Bolt with torque wrench 27-37 lbs-ft. Again 96 should be in by now.
Attached Images
 

Last edited by Wouter; 04-26-2013 at 09:24 AM.
Reply With Quote
  #66  
Old 04-26-2013, 06:33 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place woodruff key 65.
Attached Images
 
Reply With Quote
  #67  
Old 04-26-2013, 06:35 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place pump drive gear 101
Attached Images
 
Reply With Quote
  #68  
Old 04-26-2013, 06:37 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
place pump gasket 103
Attached Images
 
Reply With Quote
  #69  
Old 04-26-2013, 06:41 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
At this point I realized I forgot to place sealing ring 96 (sitting under the blue screwdriver) So I worked backwards, removed 99 and placed it.
Reply With Quote
  #70  
Old 04-26-2013, 06:50 AM
Wouter's Avatar
Wouter Wouter is offline
TT Enthusiast
 
Join Date: Jan 2007
Boat: Mastercraft Prostar 190, 1990, Indmar Ford 351w GT40P, Borg Warner 1/1 Velvet drive 71c 10-17-004, pp stargazer, Acme 13
Location: Belgium
Posts: 257
Place pump housing 104 and wrench to torque 17-22 lbs-ft. The pump housing has to be placed in the same position as when you dis-assembled (two positions are possible according to your engine's rotation) Make sure you get this right. If you don't remember check pictures if you took some or check manual and place according to your engine's rotation direction.
Attached Images
  
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


All times are GMT -4. The time now is 04:41 AM.