Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 55
Search took 0.00 seconds.
Search: Posts Made By: spievy79
Forum: Engine / Drive Train 09-28-2014, 10:50 PM
Replies: 8
Views: 345
Posted By spievy79
I have a new 40000 flamethrower coil unused,...

I have a new 40000 flamethrower coil unused, would that be ok to use in the event the old coil is not performing? Also, one other question...it is not bypassing the ballast resistor. I'm assuming its...
Forum: Engine / Drive Train 09-27-2014, 07:41 PM
Replies: 8
Views: 345
Posted By spievy79
Here's a pic I found of what it looks like.

Here's a pic I found of what it looks like.
Forum: Engine / Drive Train 09-27-2014, 07:40 PM
Replies: 8
Views: 345
Posted By spievy79
http://baylinerownersclub.org/media/kunena/attachm...

http://baylinerownersclub.org/media/kunena/attachments/vb/445635=10163-IND75-2004.jpg
Forum: Engine / Drive Train 09-27-2014, 07:32 PM
Replies: 8
Views: 345
Posted By spievy79
No, I'm sorry it is stored a half hour away. I...

No, I'm sorry it is stored a half hour away. I googled it and it says it might possibly be a type of older style electronic ignition manufactured by prestolite. I have a pertronix on my old motor...
Forum: Engine / Drive Train 09-26-2014, 09:26 AM
Replies: 8
Views: 345
Posted By spievy79
Some info on the distributor as well. 7804s 9m...

Some info on the distributor as well. 7804s 9m 2c.....e9jl1210cca. I'm also having issues identifying it. It has a screw down cap.
Forum: Engine / Drive Train 09-26-2014, 09:19 AM
Replies: 8
Views: 345
Posted By spievy79
Help identifying electronic ignition

I am going through the used PCM 5.8 I bought and the distributor has a module under the cap with a black and purple wire coming out the side. There is a prestolite coil attached to it. I also have...
Forum: Engine / Drive Train 09-22-2014, 11:11 AM
Replies: 6
Views: 259
Posted By spievy79
Appreciate it, found one!

Appreciate it, found one!
Forum: Engine / Drive Train 09-21-2014, 10:57 AM
Replies: 6
Views: 259
Posted By spievy79
Ok, thanks I'll get in touch with them and see.

Ok, thanks I'll get in touch with them and see.
Forum: Engine / Drive Train 09-21-2014, 07:50 AM
Replies: 6
Views: 259
Posted By spievy79
My apologies its a 1" shaft also.

My apologies its a 1" shaft also.
Forum: Engine / Drive Train 09-21-2014, 07:48 AM
Replies: 6
Views: 259
Posted By spievy79
cracked shaft log nut

I'm elbows deep in my engine swap and now that the old motor is out I inspected the shaft packing and noticed the nut that holds the flax has a crack through it. Can anyone direct me to a...
Forum: Engine / Drive Train 09-19-2014, 09:01 PM
Replies: 17
Views: 768
Posted By spievy79
Got it, not sure how I missed that when I was...

Got it, not sure how I missed that when I was looking. Much appreciated!
Forum: Engine / Drive Train 09-19-2014, 08:30 PM
Replies: 17
Views: 768
Posted By spievy79
I didn't want to clutter the board with a new...

I didn't want to clutter the board with a new post with a question on this swap I have on the PCM I bought. Does anyone know if I can get a reducer for my exhaust lines. The PCM exhaust riser outlet...
Forum: Engine / Drive Train 09-11-2014, 09:32 PM
Replies: 17
Views: 768
Posted By spievy79
Ok, I appreciate it. That seemed to more sense...

Ok, I appreciate it. That seemed to more sense than the commander swap to me. I knew the indmars and pcm's were fairly similar, plus I gain an extra BW out of it to boot.
Forum: Engine / Drive Train 09-11-2014, 01:02 PM
Replies: 17
Views: 768
Posted By spievy79
I came across an 87 PCM with 417 hours mated with...

I came across an 87 PCM with 417 hours mated with a 1:1 velvet drive. The boat itself was rotted out (supra ts6m). The motor is complete and he sent me a video of it running prior to pulling it. ...
Forum: Engine / Drive Train 09-07-2014, 11:05 AM
Replies: 17
Views: 768
Posted By spievy79
That makes sense to do it that way.

That makes sense to do it that way.
Forum: Engine / Drive Train 09-06-2014, 09:32 PM
Replies: 17
Views: 768
Posted By spievy79
If it were by chance a RH motor could I get a new...

If it were by chance a RH motor could I get a new tranny to reverse it to LH? He had said it was from a nautique and from what I've read some of their earlier motors were in fact RH, rather than a...
Forum: Engine / Drive Train 09-06-2014, 09:03 PM
Replies: 17
Views: 768
Posted By spievy79
I believe that it will,it's a velvet drive, sadly...

I believe that it will,it's a velvet drive, sadly I don't know the gear ratio off hand
Forum: Engine / Drive Train 09-06-2014, 08:11 PM
Replies: 17
Views: 768
Posted By spievy79
Sorry I cant upload a picture, if I had to guess...

Sorry I cant upload a picture, if I had to guess it looks like it can from an early 80's nautique so I'm not sure if its a LH or RH at this point.
Forum: Engine / Drive Train 09-06-2014, 07:45 PM
Replies: 17
Views: 768
Posted By spievy79
Replacing an Indmar 351 with a commander?

Long story short, I have a cracked block on my indmar 351. I was planning to go with a new block from rapido. However,a guy I know has a friend with a complete from top to bottom commander 351...
Forum: Engine / Drive Train 08-17-2014, 12:44 PM
Replies: 30
Views: 1,674
Posted By spievy79
Ok, I'll give that a try. Thanks again.

Ok, I'll give that a try. Thanks again.
Forum: Engine / Drive Train 08-17-2014, 11:15 AM
Replies: 30
Views: 1,674
Posted By spievy79
The reason for the dash is its age and corrosion...

The reason for the dash is its age and corrosion in the wires is all. Also, the timing has not been changed since the last time I ran it
Forum: Engine / Drive Train 08-17-2014, 11:13 AM
Replies: 30
Views: 1,674
Posted By spievy79
Can you elaborate on the posts to the solenoid? I...

Can you elaborate on the posts to the solenoid? I have four posts occupied. On top is the positive to the battery, on the side is a smaller gauge with two wires connected to it, then another small...
Forum: Engine / Drive Train 08-17-2014, 09:34 AM
Replies: 30
Views: 1,674
Posted By spievy79
I planned to get a new long block from rapido...

I planned to get a new long block from rapido marine as mentioned. They seem to have a good track record from what I've read.
Forum: Engine / Drive Train 08-17-2014, 09:32 AM
Replies: 30
Views: 1,674
Posted By spievy79
I was able to get it to fire a few times but it...

I was able to get it to fire a few times but it kept wanting to die. Now it will barely crank over at all. I cleaned off my ground, swapped all my cables to new and still the same thing. I've...
Forum: Engine / Drive Train 08-12-2014, 10:22 PM
Replies: 30
Views: 1,674
Posted By spievy79
The weld is actually holding thus far. I'm...

The weld is actually holding thus far. I'm struggling with it cranking over slowly after putting it all back together, after having water in the oil from a bad head gasket.
Showing results 1 to 25 of 55

 

All times are GMT -4. The time now is 12:52 AM.