Go Back   TeamTalk > Search Forums

Showing results 1 to 16 of 16
Search took 0.02 seconds.
Search: Posts Made By: xsvfooter
Forum: General Discussion 08-21-2006, 09:45 AM
Replies: 35
Views: 1,862
Posted By xsvfooter
That's a scary lookin pylon mount! I have a 1990...

That's a scary lookin pylon mount! I have a 1990 tristar that is mounted much different. I'd take a picture, but I'm not near the boat. Instead of a plate on the top of the fiberglass "bump", I...
Forum: Engine / Drive Train 08-14-2006, 03:31 PM
Replies: 30
Views: 1,994
Posted By xsvfooter
See attached

See attached
Forum: Engine / Drive Train 08-10-2006, 02:28 PM
Replies: 30
Views: 1,994
Posted By xsvfooter
Peterb, grab the holly rebuild pdf from the...

Peterb, grab the holly rebuild pdf from the holley website. On page 6 is a picture and procedure described to adjust the float setting. There are two methods, one while the carb in on the motor...
Forum: Engine / Drive Train 08-09-2006, 02:53 PM
Replies: 30
Views: 1,994
Posted By xsvfooter
Are you sure it's fuel starvation? Next time it...

Are you sure it's fuel starvation? Next time it stalls, before you crank the motor. Check to see if there is fuel in the bowl. You can check in the hole used to adjust the floats. You might have...
Forum: General / Other 08-09-2006, 02:40 PM
Replies: 1
Views: 417
Posted By xsvfooter
You can buy a new one at skidim.com. I replaced...

You can buy a new one at skidim.com. I replaced mine several years ago.
Forum: Engine / Drive Train 08-04-2006, 10:36 AM
Replies: 9
Views: 424
Posted By xsvfooter
Back on topic - I spoke with Eric at OJ...

Back on topic -

I spoke with Eric at OJ yesterday. Currently no plans for a SS cnc'd prop. I asked about the Cutter. Sore subject. Apparently the cutter is a copy of their prop that is made in...
Forum: Engine / Drive Train 08-04-2006, 10:34 AM
Replies: 9
Views: 424
Posted By xsvfooter
Nice meeting you guys. Between the river water...

Nice meeting you guys. Between the river water and a couple of beers at McNally's my sinuses are going to explode this morning.

Your driving for the back deeps was perfect...too bad I couldn't...
Forum: General / Other 08-03-2006, 12:45 PM
Replies: 33
Views: 4,267
Posted By xsvfooter
TMCNo1, those were my thoughts initially. I was...

TMCNo1, those were my thoughts initially. I was so unhappy with the prop I had on it I called MC to find out what the oem prop should be so I could put one on. I was stunned when they told me the 4...
Forum: General Discussion 08-02-2006, 03:39 PM
Replies: 9
Views: 595
Posted By xsvfooter
Gotta love the fox for footing. Nothing says I...

Gotta love the fox for footing. Nothing says I had a good day like the sinus headache I get after a day of footing out there!! The best time is middle to late august when you get that nice green...
Forum: Engine / Drive Train 08-02-2006, 03:28 PM
Replies: 9
Views: 424
Posted By xsvfooter
Cutter SS prop

I currently have a 13x14 OJ four blade and an ACME 431 three blade for my TriStar 190 w/454. I primarily foot and love the holeshot and holding power of the OJ. My problem is my boat is on an...
Forum: General / Other 08-02-2006, 02:50 PM
Replies: 2
Views: 397
Posted By xsvfooter
I had the same problem on my tristar 190. MC...

I had the same problem on my tristar 190. MC doesn't sell the window frame piece, just the whole window with the piece installed. I've found a few places that sell lots of hardware. I've bought...
Forum: General / Other 08-02-2006, 12:02 PM
Replies: 6
Views: 745
Posted By xsvfooter
Careful with screw holes. I've always heard...

Careful with screw holes. I've always heard there was no wood on an MC, but that's not correct. I have a 1990 TriStar and the floor panels that are removeable (in the Center) are fiberglass coated...
Forum: General / Other 08-02-2006, 11:49 AM
Replies: 33
Views: 4,267
Posted By xsvfooter
You should be getting way more than 4500 RPMs. ...

You should be getting way more than 4500 RPMs. My engine is extremely strong and I'm always concerned with over reving. I like to keep it below 5200, but depending on which prop and condition of...
Forum: Trailers 08-02-2006, 10:58 AM
Replies: 30
Views: 2,965
Posted By xsvfooter
Depending on the age of your trailer, you may...

Depending on the age of your trailer, you may need to replace the bunk boards. I replaced two of mine when I recarpeted my bunk a couple of years ago. I just used the old boards as a template.
Forum: General / Other 08-01-2006, 06:34 PM
Replies: 33
Views: 4,267
Posted By xsvfooter
I have a 1990 version in open bow. The rudder...

I have a 1990 version in open bow. The rudder showed the exact cavitation burn. The first thing you need to do is pitch that oem prop. It's a really small SS four blade that requires a brass hub...
Forum: General Discussion 08-24-2005, 03:12 PM
Replies: 18
Views: 1,143
Posted By xsvfooter
Mine's real similar. I've had my 1990 Tri-Star...

Mine's real similar. I've had my 1990 Tri-Star for 8 years now. When I was looking for a boat I wanted HP for footing and an open bow for the family. Back in 97 is was tough to find a used open...
Showing results 1 to 16 of 16

 

All times are GMT -4. The time now is 10:27 PM.