Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 267
Search took 0.02 seconds.
Search: Posts Made By: AZDave
Forum: Restorations and Refurbishments Today, 02:40 PM
Replies: 13
Views: 700
Posted By AZDave
Detailing is completed. Steering cable and rudder...

Detailing is completed. Steering cable and rudder lubed. Pylon mounts cleaned up and tightened. All fuel lines and filters replaced. Ready for carb install. I also cut the hatch cover back 1", and...
Forum: Restorations and Refurbishments 10-16-2014, 09:39 PM
Replies: 13
Views: 700
Posted By AZDave
The 93 set up is much more robust. I PB blasted...

The 93 set up is much more robust. I PB blasted all bolts and tightened a 1/4-1/2 turn here and there. Should be fine.
Forum: Restorations and Refurbishments 10-16-2014, 05:17 PM
Replies: 13
Views: 700
Posted By AZDave
I don't know. I would take all the hardware out...

I don't know. I would take all the hardware out and inspect the hole. Possibly refill with glass and re tap
Forum: Restorations and Refurbishments 10-16-2014, 09:57 AM
Replies: 13
Views: 700
Posted By AZDave
Any suggestions on an easy way to make that bilge...

Any suggestions on an easy way to make that bilge look shiny?
Forum: Restorations and Refurbishments 10-16-2014, 09:56 AM
Replies: 13
Views: 700
Posted By AZDave
Too late. But I have heard about the 4160 being...

Too late. But I have heard about the 4160 being better. I have also seen 4160's have major issues as well on our lake. It will be the next step, for sure!
Forum: Restorations and Refurbishments 10-15-2014, 03:44 PM
Replies: 13
Views: 700
Posted By AZDave
1993 Stars and Stripes Bilge Detailing

I have some time off, and my carb is being rebuilt, so I replaced the gas line and was disgusted with the bilge area. I removed everything. I thought I would address the pylon bolts and tighten them...
Forum: Engine / Drive Train 10-14-2014, 11:59 AM
Replies: 12
Views: 428
Posted By AZDave
OK! I think it faces the back because the hose...

OK! I think it faces the back because the hose would have to make a pretty good u turn otherwise. Thanks! I am in no hurry, getting carb rebuilt now.
Forum: Engine / Drive Train 10-14-2014, 08:19 AM
Replies: 12
Views: 428
Posted By AZDave
I guess it does not matter. I just forgot the...

I guess it does not matter. I just forgot the origonal position. It was either pointed directly towards the bow, or the stern. I was hoping another 190 Prostar would offer a picture. I have searched...
Forum: Engine / Drive Train 10-13-2014, 10:47 PM
Replies: 12
Views: 428
Posted By AZDave
So, facing the rear of the boat, the sending unit...

So, facing the rear of the boat, the sending unit is to the left of the outlet elbow. That does not look like a 190 tank from the picture. Mine is a 190.
Forum: Engine / Drive Train 10-13-2014, 08:00 PM
Replies: 12
Views: 428
Posted By AZDave
I guess this is the outlet to the engine, is this...

I guess this is the outlet to the engine, is this oriented correctly?
Forum: Engine / Drive Train 10-13-2014, 04:17 PM
Replies: 12
Views: 428
Posted By AZDave
93 Pro Star Gas Tank Inlet

I pulled my tank, but forgot how the inlet tube on the top is oriented to attach the hose, after taking it out to clean the tank and check the fuel pick up. Does it face towards the front, or rear...
Forum: For Sale: Boats 10-11-2014, 07:03 PM
Replies: 26
Views: 2,518
Posted By AZDave
Awfully tempting. How much to ship to AZ?...

Awfully tempting. How much to ship to AZ? Probably 2 thousand. That would be the deal breaker for me.
Forum: Towers 10-11-2014, 03:25 PM
Replies: 637
Views: 74,897
Posted By AZDave
Boat just lost 1/4 of it's value. What makes me...

Boat just lost 1/4 of it's value. What makes me cringe is the fact that once you start adding ballast and hammering these boats in rough water, they are never the same.
Forum: Trailers 10-04-2014, 08:21 PM
Replies: 2
Views: 191
Posted By AZDave
I had the same trailer. Great looking trailer....

I had the same trailer. Great looking trailer. Numerous flaws. Bow roller notoriously chewed up keel. Brake line rubber hose rotted. Crossmember by axel had a tendency to rot. Prop guard needed...
Forum: Waterskiing & Barefooting 09-27-2014, 01:15 PM
Replies: 5
Views: 353
Posted By AZDave
I have 2 years on this ski and absolutely love...

I have 2 years on this ski and absolutely love it. Bought mine at Wiley's with the Wiley's bindings. I am a course skier. 30-32 mph 15 off.
Forum: Engine / Drive Train 09-26-2014, 10:11 AM
Replies: 13
Views: 413
Posted By AZDave
I set the idle mixture to factory, and pulled 3...

I set the idle mixture to factory, and pulled 3 sets. Ran perfect. Upon sitting for 45 minutes, it would start, but not idle. I then backed each mixture screw out 1/2 turn, boat started, and idled to...
Forum: Engine / Drive Train 09-17-2014, 06:11 PM
Replies: 13
Views: 413
Posted By AZDave
You are right, I have a 4010 kit, but the 703-53...

You are right, I have a 4010 kit, but the 703-53 is for marine use. I will let you know if and when I need this rebuilt. Thanks for all the help!
Forum: Engine / Drive Train 09-17-2014, 02:27 PM
Replies: 13
Views: 413
Posted By AZDave
It is R50483

It is R50483
Forum: Engine / Drive Train 09-17-2014, 12:59 PM
Replies: 13
Views: 413
Posted By AZDave
Where are these numbers? I got FIJL-9510-EA and...

Where are these numbers? I got FIJL-9510-EA and 1492#
Forum: Engine / Drive Train 09-17-2014, 10:33 AM
Replies: 13
Views: 413
Posted By AZDave
Never. So it appears by adjusting the one mixture...

Never. So it appears by adjusting the one mixture screw, I am not balanced. If it gets worse, I think it is rebuild time. I will lightly seat both, back them out 1 and 1/2 and adjust the idle speed...
Forum: Engine / Drive Train 09-17-2014, 09:17 AM
Replies: 13
Views: 413
Posted By AZDave
4010 Idle Issue

Up until yesterday, no issues with the carb. 800 hours. I just wanted the idle speed to come up a little, and did some slight tweaking on the idle mixture screw by the electric choke and the idle...
Forum: Trailers 09-12-2014, 07:05 PM
Replies: 7
Views: 621
Posted By AZDave
I had the same xmember fail on my 190. I sold the...

I had the same xmember fail on my 190. I sold the fenders, tires, jack, and scrapped the trailer frame for $200. Firebird did my trailer in, what got yours?
Forum: General Discussion 09-11-2014, 07:49 PM
Replies: 131
Views: 9,496
Posted By AZDave
My buddy had an old Malibu, and if the sun hit it...

My buddy had an old Malibu, and if the sun hit it just right you could make out the words "Freedom Skier". Anyone know about that?
Forum: General Discussion 09-06-2014, 01:57 PM
Replies: 32
Views: 1,986
Posted By AZDave
I am at Firebird, brackish would be the PC...

I am at Firebird, brackish would be the PC description of the water quality. Water temp 90+. Yuk.
Forum: General Discussion 09-06-2014, 09:25 AM
Replies: 32
Views: 1,986
Posted By AZDave
At least another 30-45 days of 100 degrees here,...

At least another 30-45 days of 100 degrees here, then a good month or 2, followed by 2 months of 70 degree highs. Then it warms up again. Not very comfortable skiing during the day now, but mornings...
Showing results 1 to 25 of 267

 

All times are GMT -4. The time now is 11:09 PM.