Go Back   TeamTalk > Search Forums

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: Mfletch80
Forum: MasterCraft 06-10-2017, 02:11 PM
Replies: 14
Views: 4,151
Posted By Mfletch80
I am not going to be able to pull it out for...

I am not going to be able to pull it out for another couple of weeks. One other thought would be the plug wires. Would a problem with these be in neutral as well as under power with increased...
Forum: MasterCraft 06-05-2017, 09:17 AM
Replies: 14
Views: 4,151
Posted By Mfletch80
That helps. Will let you know what they find...

That helps. Will let you know what they find after I take it in. I appreciate all of your help and expertise. Mike
Forum: MasterCraft 06-03-2017, 06:36 AM
Replies: 14
Views: 4,151
Posted By Mfletch80
I looked and could not really tell what I had....

I looked and could not really tell what I had. Any chance this could be a distributor? Not sure when I last changed this?
Forum: MasterCraft 05-27-2017, 04:38 PM
Replies: 14
Views: 4,151
Posted By Mfletch80
Fluid was ok before putting in. Have not...

Fluid was ok before putting in. Have not rechecked again. Just changed plugs, oil and impeller as well. Could that be relevant?
Not sure what kind of tranny. Can I see that by looking?
Forum: MasterCraft 05-27-2017, 03:17 PM
Replies: 14
Views: 4,151
Posted By Mfletch80
No, neutral seems fine with high rpms. Reverse...

No, neutral seems fine with high rpms. Reverse seemed to make a funny and different sounds as well.
Thanks
Forum: Off Topic Discussion 05-27-2017, 05:44 AM
Replies: 2
Views: 853
Posted By Mfletch80
Mike, Sounds like you had some fluid in the bursa...

Mike,
Sounds like you had some fluid in the bursa just above the knee and it may have ruptured. This would explain what you described, I believe. Also, not sure you had gout if not having a lot of...
Forum: MasterCraft 05-27-2017, 05:39 AM
Replies: 14
Views: 4,151
Posted By Mfletch80
Thanks so much for the help. If it were the...

Thanks so much for the help. If it were the damper plate, would you not expect to hear it even below 2000 rpm's?
Forum: MasterCraft 05-26-2017, 04:50 PM
Replies: 14
Views: 4,151
Posted By Mfletch80
Does this require a trip to the shop to diagnose...

Does this require a trip to the shop to diagnose and correct? Anything more I can do to confirm before pulling it out of the water again? Is it a big job?
Forum: MasterCraft 05-26-2017, 08:56 AM
Replies: 14
Views: 4,151
Posted By Mfletch80
It is 1994, EFI, and has 650 hrs. No sound when...

It is 1994, EFI, and has 650 hrs. No sound when below 2000 rpm. The sound is intermittent. Where you able to access my video?
Thanks
Mike
Forum: MasterCraft 05-25-2017, 07:12 PM
Replies: 14
Views: 4,151
Posted By Mfletch80
Unhappy Maristar 225 EFI Indmar engine knocking noise

Put the boat in today, started right up, but when I went past about 2000-2500 rpm, there was a knocking noise. I just changed oil, impeller and plugs before putting it in. There is another noise in...
Forum: Restorations and Refurbishments 07-09-2016, 07:21 PM
Replies: 46
Views: 17,593
Posted By Mfletch80
I was able to find a pair in Utah. Thanks for...

I was able to find a pair in Utah. Thanks for your help.
Forum: Restorations and Refurbishments 07-07-2016, 01:18 PM
Replies: 46
Views: 17,593
Posted By Mfletch80
Thanks much. I have a call in to them to see if...

Thanks much. I have a call in to them to see if they still carry the larger one. Online they only had the 3 1/8" flapper.
Forum: Restorations and Refurbishments 07-07-2016, 12:24 PM
Replies: 46
Views: 17,593
Posted By Mfletch80
Exhaust flappers for 1994 Maristar 225

I have read with interest this thread about the 5 3/8" exhaust flappers for the older Mastercrafts. I need one for my 1994 Maristar. I have reviewed the leads in this thread and so far no luck. I...
Showing results 1 to 13 of 13

 

All times are GMT -4. The time now is 08:03 PM.


2018