Forum: Electrical
04-14-2011, 05:13 PM
|
|
Replies: 5
Views: 528
|
Forum: Electrical
04-14-2011, 02:55 PM
|
|
Replies: 5
Views: 528
Starter/electrical problem
I have a 1987 prostar 190 that I can't seem to get started. Battery is good, and just replaced the starter solenoid. I have about 12.5 volts on the battery side of the solenoid before trying to...
|
Forum: Engine / Drive Train
04-01-2009, 04:32 PM
|
|
Replies: 20
Views: 5,244
|
Forum: Engine / Drive Train
03-31-2009, 05:17 PM
|
|
Replies: 20
Views: 5,244
oil for 87 prostar
I have been using rotella t for the 2 years I have owned the boat, but I remember reading somewhere that they stopped putting in an additive that is needed for the flat tappet cam in my engine. Im...
|
Forum: Electrical
07-25-2008, 06:54 PM
|
|
Replies: 7
Views: 448
|
Forum: Electrical
07-25-2008, 02:27 PM
|
|
Replies: 7
Views: 448
I would pull the starter an get it tested at...
I would pull the starter an get it tested at autozone then. may need a new one. you can get it rebuilt cheaper than buying a new marine one. just make sure to tell them its for marine application
|
Forum: Electrical
07-24-2008, 07:38 PM
|
|
Replies: 7
Views: 448
|
Forum: Wakeboarding & Wakeskating
07-24-2008, 05:23 PM
|
|
Replies: 21
Views: 2,108
|
Forum: Wakeboarding & Wakeskating
07-24-2008, 05:21 PM
|
|
Replies: 21
Views: 2,108
For now i think im just gonna try to land that...
For now i think im just gonna try to land that ollie bs180. Then i can progress to inside/out, an 1wake like you said MCdriven. i did that with my hs fs180s and helped a lot.
Vision i understand...
|
Forum: Wakeboarding & Wakeskating
07-24-2008, 03:00 PM
|
|
Replies: 21
Views: 2,108
|
Forum: Wakeboarding & Wakeskating
07-24-2008, 02:43 PM
|
|
Replies: 21
Views: 2,108
i can get the handle pass on surface spins very...
i can get the handle pass on surface spins very easily.. is it correct for ollie bs 180 to edge out hard then flatten quickly , and pop the spin. Doing it like that well lessen the tension so i dont...
|
Forum: General Discussion
07-24-2008, 02:37 PM
|
|
Replies: 26
Views: 1,585
|
Forum: General Discussion
07-24-2008, 01:58 PM
|
|
Replies: 26
Views: 1,585
|
Forum: General Discussion
07-24-2008, 01:17 PM
|
|
Replies: 10
Views: 825
|
Forum: Wakeboarding & Wakeskating
07-24-2008, 09:53 AM
|
|
Replies: 21
Views: 2,108
|
Forum: Wakeboarding & Wakeskating
07-23-2008, 09:22 PM
|
|
Replies: 21
Views: 2,108
|
Forum: Wakeboarding & Wakeskating
07-23-2008, 09:19 PM
|
|
Replies: 21
Views: 2,108
So i got to ride for the first time in like 4...
So i got to ride for the first time in like 4 weeks this morning now that my boats running again:).. I felt like i started gettin some good pop on my jumps.. I was cuttin out, then i would sit and...
|
Forum: Wakeboarding & Wakeskating
07-22-2008, 09:00 PM
|
|
Replies: 21
Views: 2,108
Ollie edge
I got the chance to ride with a very good rider and he told me to practice jumping w2w using an ollie edge instead of progressive edge. he said its more for w2w spins and tricks where you need low...
|
Forum: Electrical
07-22-2008, 08:52 PM
|
|
Replies: 5
Views: 1,795
Problem solved. I cleaned all the grounding...
Problem solved. I cleaned all the grounding locations again. I decided to try using the old solenoid again and after i tightened everything up, she fired right up. I cant wait to hit the lake early...
|
Forum: Electrical
07-22-2008, 05:00 PM
|
|
Replies: 5
Views: 1,795
|
Forum: Electrical
07-22-2008, 04:25 PM
|
|
Replies: 5
Views: 1,795
|
Forum: Electrical
07-21-2008, 09:26 PM
|
|
Replies: 5
Views: 1,795
boat wont start.. HELP
My 87 prostar has been sidelined for a couple of weeks because of a bent strut an shaft. I have finished the install and aligning the engine and decided to run the engine since it hasnt been running...
|