Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 500
Search took 0.09 seconds.
Search: Posts Made By: j.mccreight@hotmail.com
Forum: Engine / Drive Train Yesterday, 11:58 PM
Replies: 16
Views: 452
When I swapped out my camshaft I degreed and...

When I swapped out my camshaft I degreed and measured the original before replacing, heres what I came up with.

1989 250HP 351w Indmar, measurements @ .050"
INT OPEN -11BTDC
INT CLO 41ABDC
EXH...
Forum: Engine / Drive Train Yesterday, 08:11 PM
Replies: 34
Views: 929
Looking good, if I had the blue "mastercraft...

Looking good, if I had the blue "mastercraft power" aluminum valve covers I would send them to ya, but I only have the mastercraft chrome steel valve covers that aren't in any better shape than your...
Forum: Engine / Drive Train 04-22-2014, 10:10 PM
Replies: 34
Views: 929
My painter did it recently in his free time....

My painter did it recently in his free time. Called Silver Ice Metallic really shines in the sun, I won't say which MFG uses that paint code as I may burn for putting a non ford color on . LOL
Forum: Engine / Drive Train 04-22-2014, 10:05 PM
Replies: 34
Views: 929
It's my "project" '86 Mustang LX coupe

It's my "project" '86 Mustang LX coupe
Forum: Engine / Drive Train 04-22-2014, 10:01 PM
Replies: 34
Views: 929
Yes I painted the long block as an assembly, then...

Yes I painted the long block as an assembly, then painted all other components separately.
Forum: Engine / Drive Train 04-22-2014, 09:37 PM
Replies: 34
Views: 929
Looking good, dupli color engine paint with...

Looking good, dupli color engine paint with ceramic is good stuff it dries with a hard coating tough to chip after its dried. I just painted my little 302 with this paint and it came out great.
Forum: Audio/Stereo 04-22-2014, 06:32 PM
Replies: 15
Views: 332
So...I guess after all that the bulletlines...

So...I guess after all that the bulletlines recommendation was correct after all...
Forum: Off Topic Discussion 04-20-2014, 08:15 PM
Replies: 2,017
1
Views: 76,860
..............

..............
Forum: Ballast 04-20-2014, 08:11 PM
Replies: 6
Views: 221
Don't have ballast but the green ones are what...

Don't have ballast but the green ones are what this forum says to use along with polishing the inside.
Forum: Engine / Drive Train 04-20-2014, 08:09 PM
Replies: 1
Views: 96
Perhaps all the fluid just overtook the seal and...

Perhaps all the fluid just overtook the seal and it leaked from sitting? I would clean it up, top off transmission with fluid and water test for leaks. Sometimes seals do some odd things.
Forum: General Discussion 04-20-2014, 08:06 PM
Replies: 5
Views: 192
something like this?...

something like this? http://www.oempartsllc.com/gaugetrimteleflex72742ablackbezelredinternetionalnew-1-2-1-1.aspx
perhaps you need to go with a gps version?
Forum: General Discussion 04-17-2014, 11:32 PM
Replies: 13
Views: 437
Positive to positive, negative to negative,...

Positive to positive, negative to negative, called a parallel connection. Both batteries should be should be of the same shape and size for best results
Forum: Restorations and Refurbishments 04-16-2014, 09:46 PM
Replies: 29
Views: 1,198
Mikeg has used http://www.evapo-rust.com/...

Mikeg has used http://www.evapo-rust.com/ personally I would take them to the machine shop and have them boiled.
Forum: Restorations and Refurbishments 04-15-2014, 11:18 PM
Replies: 29
Views: 1,198
This is absolutely true, I first installed the...

This is absolutely true, I first installed the same valve covers you bought and a weiand intake didn't treat either, after a few weeks the bare aluminum started to dull and corrode, fresh water only...
Forum: Engine / Drive Train 04-15-2014, 11:12 PM
Replies: 34
Views: 929
nice choice... here's mine

nice choice...

here's mine
Forum: Engine / Drive Train 04-15-2014, 10:38 PM
Replies: 3
Views: 130
Indmar Spec. Oil Pressure at Idle 4PSI (41kPa)...

Indmar Spec.
Oil Pressure at Idle 4PSI (41kPa) Minimum - Hot
Oil Pressure at 2000 RPM 18 PSI (124 kPa) Minimum - Hot

Sounds like your just fine...
Forum: Engine / Drive Train 04-15-2014, 10:24 PM
Replies: 47
Views: 1,737
I doubt you actually had any voltage issues on...

I doubt you actually had any voltage issues on the engine and engine harness, I didn't all my problems were under the dash.

I personally won't run Petronix, I've heard way to many problems...
Forum: Electrical 04-15-2014, 08:42 PM
Replies: 17
Views: 722
Nice job, if I'd known you needed a speedometer...

Nice job, if I'd known you needed a speedometer head I could have sent you one.
Forum: Engine / Drive Train 04-15-2014, 08:37 PM
Replies: 47
Views: 1,737
Yes 31 dwell is spec...

Yes 31 dwell is spec...
Forum: Engine / Drive Train 04-15-2014, 08:27 AM
Replies: 10
Views: 166
Chevy 350 was an available option on these boats...

Chevy 350 was an available option on these boats back then, I do not know however which carb was on the chevy, all Ford's had the holley.
Forum: Engine / Drive Train 04-14-2014, 11:25 PM
Replies: 34
Views: 929
Tapped into runner, using the weiand with the...

Tapped into runner, using the weiand with the factory 1.25" spacer was not enough clearance for my liking to the motor box, never gave it a second thought. If you use the performer you might get away...
Forum: Engine / Drive Train 04-14-2014, 11:10 PM
Replies: 34
Views: 929
Adjusting is all you need, be sure to use the...

Adjusting is all you need, be sure to use the vacuum gauge method.
Forum: Engine / Drive Train 04-14-2014, 10:56 PM
Replies: 34
Views: 929
With your hotter than stock 351w, You could use...

With your hotter than stock 351w, You could use the weiand stealth intake, slightly less tall than the rpm but flows just as good as the rpm. It clears on my boat. I don't know on your year. If you...
Forum: Engine / Drive Train 04-14-2014, 04:03 PM
Replies: 52
Views: 1,893
Wow 275hp, it's not even worth changing the h/c/i...

Wow 275hp, it's not even worth changing the h/c/i for 25 hp. Me thinks your simulator is way wrong. Even the mustang guys with a 302, p heads and a similar f303 cam is about 330 hp at the crank, very...
Forum: Wanted to Buy 04-14-2014, 03:50 PM
Replies: 2
Views: 80
http://www.boardstop.com/product_info.php?products...

http://www.boardstop.com/product_info.php?products_id=2762
Showing results 1 to 25 of 500

 

All times are GMT -4. The time now is 05:57 AM.