Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 167
Search took 0.01 seconds.
Search: Posts Made By: tockit
Forum: Electrical 07-26-2015, 01:07 AM
Replies: 23
Views: 504
Posted By tockit
The connector on my 89 TriStar, back at the...

The connector on my 89 TriStar, back at the transmission/circuit breaker terminal develop a bad connection one time. The connector is like an 8 pin connector that connects ignition switch, coil...
Forum: Electrical 07-22-2015, 01:49 AM
Replies: 4
Views: 188
Posted By tockit
What kind of condition are your battery cables?...

What kind of condition are your battery cables? Mine were in bad shape. They got hot during starting and had a 5 volt current drop. Put your meter on your starter terminal during the start sequence...
Forum: Engine / Drive Train 07-01-2015, 04:12 PM
Replies: 8
Views: 318
Posted By tockit
(LH) isn't reverse rotation?

(LH) isn't reverse rotation?
Forum: Engine / Drive Train 07-01-2015, 04:07 PM
Replies: 8
Views: 318
Posted By tockit
You're kind of confusing me with this statement....

You're kind of confusing me with this statement. Is my camshaft standard rotation or reverse rotation (LH)?
Forum: Engine / Drive Train 07-01-2015, 04:02 PM
Replies: 8
Views: 318
Posted By tockit
If the bottom of your picture is the front of the...

If the bottom of your picture is the front of the engine, then the cam drive gear is cut the same as the one in my picture. My picture is rotated 180 degrees from yours. Is that the way you see it?
Forum: Engine / Drive Train 07-01-2015, 01:41 PM
Replies: 8
Views: 318
Posted By tockit
Camshaft Question?

I've attached a picture of a camshaft drive gear out of the short block I'm replacing in my boat.
The orientation is so that the top of the picture is the front of the engine, and you're looking...
Forum: Restorations and Refurbishments 05-25-2015, 02:43 AM
Replies: 14
Views: 1,075
Posted By tockit
Very nice A.P! You did an incredible job!!!

Very nice A.P! You did an incredible job!!!
Forum: Engine / Drive Train 09-18-2014, 10:30 PM
Replies: 3
Views: 378
Posted By tockit
PCM, Indmar or Ford?

Ok, been meaning to ask this for weeks but keep forgetting.
I was looking at gaskets on SkiDim's website and there are 2 or 3 options on some things.

My boat is a 1989 Tristar, with an Indmar/Ford...
Forum: Engine / Drive Train 09-16-2014, 09:12 PM
Replies: 10
Views: 482
Posted By tockit
I sure hope so! Tired of fooling with this thing....

I sure hope so! Tired of fooling with this thing. :rolleyes:
Forum: Engine / Drive Train 09-16-2014, 09:06 PM
Replies: 10
Views: 482
Posted By tockit
Getting spark, not sure about fuel.

Getting spark, not sure about fuel.
Forum: Engine / Drive Train 09-16-2014, 09:01 PM
Replies: 10
Views: 482
Posted By tockit
Spark is good on that cylinder. I've reclocked...

Spark is good on that cylinder. I've reclocked the distributor cap to see if it changed cylinders. It did not. I've switched plugs from other cylinders that were working, still no combustion....
Has...
Forum: Engine / Drive Train 09-16-2014, 08:55 PM
Replies: 10
Views: 482
Posted By tockit
Whiskey, That's the main thing I'm leaning...

Whiskey,
That's the main thing I'm leaning towards right now. I used the Edelbrock Performer intake and it has a 3/8" vacuum port in the #4 intake runner (same cylinder that's cold). I teed into it...
Forum: Engine / Drive Train 09-16-2014, 06:37 AM
Replies: 10
Views: 482
Posted By tockit
Intake Question?

I recently put a set of GT40P heads and an Edelbrock Performer Intake (non-EGR) on my 351W. Now the #4 cylinder isn't firing.

I've checked compression in that cylinder, which is good (160PSI),...
Forum: Engine / Drive Train 09-01-2014, 10:56 PM
Replies: 25
Views: 1,405
Posted By tockit
That's all the pictures I have for now. I was...

That's all the pictures I have for now. I was running out of time this afternoon. I got it running and my initial timing set with no water in the oil after an hour or so of running!
Heading to the...
Forum: Engine / Drive Train 09-01-2014, 10:52 PM
Replies: 25
Views: 1,405
Posted By tockit
I also went with an Edelbrock Performer aluminum...

I also went with an Edelbrock Performer aluminum intake, which I read adds a little quicker throttle response when used with the GT40P heads on the 351:
Forum: Engine / Drive Train 09-01-2014, 10:47 PM
Replies: 25
Views: 1,405
Posted By tockit
With no visible cracks in the heads or cylinders,...

With no visible cracks in the heads or cylinders, and a blown head gasket, I was unsure of my next move. I searched the forums, etc, and figured it had to have been from the head gasket leaking water...
Forum: Engine / Drive Train 09-01-2014, 10:29 PM
Replies: 25
Views: 1,405
Posted By tockit
Afterwards, I tore into it to try to find the...

Afterwards, I tore into it to try to find the source of the milky oil. The heads, nor the block had no visible cracks. I did find a blown head gasket at the #4 cylinder, which may have been that way...
Forum: Engine / Drive Train 09-01-2014, 10:27 PM
Replies: 25
Views: 1,405
Posted By tockit
Update on my water in the oil issue. I finally...

Update on my water in the oil issue. I finally got things sorted out this weekend. Thought I'd post what I found to maybe help someone else out down the road.
To go back over what happened, I had a...
Forum: Engine / Drive Train 08-23-2014, 11:23 AM
Replies: 25
Views: 1,405
Posted By tockit
I sure hope you're right Repeat! I ordered new...

I sure hope you're right Repeat! I ordered new headgasket's, etc, and I'll post the results later.
Maybe this will help someone else troubleshoot their engine in the future?
Forum: Engine / Drive Train 08-21-2014, 08:33 PM
Replies: 25
Views: 1,405
Posted By tockit
It did smoke some. Is there any way to verify a...

It did smoke some. Is there any way to verify a cracked cylinder wall below the piston without pulling the engine and tearing it down? Would this show up on a compression test?
Forum: Engine / Drive Train 08-21-2014, 08:29 PM
Replies: 9
Views: 567
Posted By tockit
Mine made a noise like you describe last year and...

Mine made a noise like you describe last year and it was the damper plate.
Forum: Engine / Drive Train 08-19-2014, 11:20 PM
Replies: 25
Views: 1,405
Posted By tockit
I don't have a picture of the piston and cylinder...

I don't have a picture of the piston and cylinder head, but it doesn't really look that much different than the others. I cleaned everything up and looked at all the mating surfaces around the water...
Forum: Engine / Drive Train 08-19-2014, 06:19 PM
Replies: 25
Views: 1,405
Posted By tockit
Here's a picture of the head gasket. Not a very...

Here's a picture of the head gasket. Not a very good one.
Forum: Engine / Drive Train 08-19-2014, 02:07 PM
Replies: 25
Views: 1,405
Posted By tockit
I don't see any evidence of a crack. I guess I...

I don't see any evidence of a crack. I guess I could hit everything. I did find one of the head gaskets on the aft right cylinder with the cylinder ring in the gasket split. I was wondering if that...
Forum: Engine / Drive Train 08-19-2014, 01:49 PM
Replies: 25
Views: 1,405
Posted By tockit
Since you mentioned a problem in the valley, one...

Since you mentioned a problem in the valley, one thing I found that might be my problem is a hole in the valley behind the forward wall, aft of where the distributor drops into the block. That paper...
Showing results 1 to 25 of 167

 

All times are GMT -4. The time now is 08:23 AM.