Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: TRBenj
Forum: Engine / Drive Train Today, 09:13 AM
Replies: 3
Views: 110
Posted By TRBenj
Dampers are transmission specific and are...

Dampers are transmission specific and are "universal" on the engine side. If you have a velvet drive, the ebasic damper will work. SkiDIM sells the same piece, but they mistakenly list it as a "GM...
Forum: Engine / Drive Train 08-14-2014, 11:34 AM
Replies: 20
Views: 708
Posted By TRBenj
Any air leak before the RWP is certainly going to...

Any air leak before the RWP is certainly going to cause an overheat (at idle), and you're right- a strainer bowl that is cracked, too loose, or reinstalled with a broken (or missing) seal is going to...
Forum: Engine / Drive Train 08-13-2014, 07:52 AM
Replies: 20
Views: 708
Posted By TRBenj
You're not alone, Doug... Cc has been installing...

You're not alone, Doug... Cc has been installing strainers as standard equipment since ~1983. The post above is the first I've heard about them being problematic! Now, the flush pro on the other...
Forum: Engine / Drive Train 08-01-2014, 08:40 AM
Replies: 37
Views: 1,646
Posted By TRBenj
I'm curious how anyone can tell whether the...

I'm curious how anyone can tell whether the engine is lean based on that pic... Not enough information to tell by looking at the tip alone. Width of the soot ring at the base is the only really way...
Forum: Engine / Drive Train 07-31-2014, 03:01 PM
Replies: 37
Views: 1,646
Posted By TRBenj
MEFI BURN and Ecm Tuning

Can't tell much from the photos... Fuel burns pretty clean these days. Certainly not overly rich but not silvery in color either (indicative) of pistons melting) which is a good thing. If you...
Forum: Engine / Drive Train 07-30-2014, 09:58 AM
Replies: 13
Views: 409
Posted By TRBenj
I didn't look up the pistons, but i would imagine...

I didn't look up the pistons, but i would imagine that those numbers are in the ballpark if they're specific to the 351w. Bore, stroke, Piston volume and head chamber volume get you CR for the most...
Forum: Engine / Drive Train 07-29-2014, 01:49 PM
Replies: 13
Views: 409
Posted By TRBenj
250hp

250hp
Forum: General Discussion 07-29-2014, 01:46 PM
Replies: 39
Views: 1,448
Posted By TRBenj
Oddball boat, oddball set up... I guarantee acme...

Oddball boat, oddball set up... I guarantee acme has no data on your exact boat the way you're using it- probably don't have anything close. They based a recommendation off your current prop, which...
Forum: General Discussion 07-23-2014, 08:57 AM
Replies: 1
Views: 183
Posted By TRBenj
Presumably you have the 1.52:1 powerslot tranny? ...

Presumably you have the 1.52:1 powerslot tranny?

Generally speaking, you'll pick up a good bit of performance and keep revs where they need to be by switching to a modern CNC prop with a similar...
Forum: Off Topic Discussion 06-13-2014, 06:56 AM
Replies: 26
Views: 1,064
Posted By TRBenj
I have found the free GPS/speedometer phone apps...

I have found the free GPS/speedometer phone apps to be fairly inaccurate. I have verified the Navionics app to be almost spot on with my garmin etrex though. $10 well spent.
Forum: Engine / Drive Train 06-13-2014, 06:49 AM
Replies: 22
Views: 787
Posted By TRBenj
If your carbureted boat requires pumping of the...

If your carbureted boat requires pumping of the throttle to start when warm, then it's not dialed in. It doesn't matter how old I am or who your dad was! I've seen plenty of high hour boats that...
Forum: Engine / Drive Train 06-10-2014, 09:45 PM
Replies: 22
Views: 787
Posted By TRBenj
Marine Holley baseplates supposedly have sealed...

Marine Holley baseplates supposedly have sealed (o-ring?) throttle shafts. I've never taken one far enough apart to confirm this myself, but the only carbs I've seen leak fuel from the throttle...
Forum: Off Topic Discussion 06-09-2014, 03:14 PM
Replies: 60
Views: 2,916
Posted By TRBenj
The few posts that stated that the 542 is a RH...

The few posts that stated that the 542 is a RH prop are correct. 540/542 are the RH equivalents of the 541/543. All RH Acmes have even model numbers.

Eric at OJ has always been great to work with....
Forum: General Discussion 05-27-2014, 05:28 PM
Replies: 32
Views: 1,417
Posted By TRBenj
If I were selling a boat that I had invested a...

If I were selling a boat that I had invested a lot in (time, money, sweat) then I would absolutely be picky about who buys it. Allowing your old baby to go to someone who you know will wreck it- no...
Forum: Restorations and Refurbishments 05-27-2014, 05:19 PM
Replies: 142
Views: 21,539
Posted By TRBenj
Someone familiar with how MC built that boat...

Someone familiar with how MC built that boat originally might need to comment on that cracking. Were they installing a pre-fabbed "bilge pan" as it appears? I know that's how Malibu builds their...
Forum: Engine / Drive Train 05-27-2014, 05:12 PM
Replies: 13
Views: 621
Posted By TRBenj
Soak any and all suspect hard parts in carb...

Soak any and all suspect hard parts in carb cleaner for a few hours. I mean submerge them. Then repeat what you've done.

I assume you've swapped in a different carb and the issue cleared up?

I'm...
Forum: General Discussion 05-22-2014, 05:36 PM
Replies: 16
Views: 408
Posted By TRBenj
All of the hydraulic lifts of this style that I...

All of the hydraulic lifts of this style that I own (Nyman/Basta, Shoremaster, Sunstream) utilize power up/power down/hold style hydraulic systems. They do not require any weight on the bunks to...
Forum: For Sale: Parts & Accessories 05-14-2014, 05:04 PM
Replies: 12
Views: 899
Posted By TRBenj
One last bump before it goes to...

One last bump before it goes to ebay.

TRBenj@gmail.com
Forum: For Sale: Parts & Accessories 05-07-2014, 10:09 AM
Replies: 12
Views: 899
Posted By TRBenj
All of my assembled chrome bezel speedos are gone...

All of my assembled chrome bezel speedos are gone as of now, but I do have plenty of cores that I can put together if need be.

I also have this nice MC faced 2025 all ready to go. Its not NOS,...
Forum: Engine / Drive Train 05-02-2014, 10:56 AM
Replies: 10
Views: 687
Posted By TRBenj
I assume the point you are comparing to is where...

I assume the point you are comparing to is where the shaft spins freely in the strut?

If so, then I still suggest:
Forum: General / Other 05-01-2014, 11:16 AM
Replies: 6
Views: 265
Posted By TRBenj
True story. Older BFI's do in fact have an allen...

True story. Older BFI's do in fact have an allen head set screw in place of the spring loaded button that holds the 2 halves together. Theyre not coming apart even if you dont tighten it, though.
Forum: Engine / Drive Train 05-01-2014, 08:10 AM
Replies: 44
Views: 2,413
Posted By TRBenj
Well there you have it... you have a...

Well there you have it... you have a (non-original) dual taper shaft. That info (or a picture) would have been much more helpful at the beginning of the thread! A puller and a hammer should...
Forum: Engine / Drive Train 04-30-2014, 11:23 AM
Replies: 44
Views: 2,413
Posted By TRBenj
Dual taper prop shafts are out there, but are not...

Dual taper prop shafts are out there, but are not standard on all boats. Single taper (on the prop end) is the standard for most direct drives, especially older ones. I believe we have established...
Forum: Engine / Drive Train 04-21-2014, 06:25 PM
Replies: 10
Views: 687
Posted By TRBenj
A left/right alignment issue may indicate a bent...

A left/right alignment issue may indicate a bent strut. Better pop under the boat and take a close look. A small framing square and a tape measure may help you spot a bend that can be difficult to...
Forum: Engine / Drive Train 04-18-2014, 09:45 AM
Replies: 10
Views: 687
Posted By TRBenj
How/where are you supporting the driveshaft...

How/where are you supporting the driveshaft during all of this? Is it being held in place where it is aligned in the strut (where it spins freely)? Or are you letting it sag under its own weight? ...
Showing results 1 to 25 of 500

 

All times are GMT -4. The time now is 12:31 PM.