Go Back   TeamTalk > Search Forums

Showing results 1 to 21 of 21
Search took 0.00 seconds.
Search: Posts Made By: KWSC
Forum: General Discussion Today, 11:44 AM
Replies: 0
Views: 1
Posted By KWSC
Mastercraft logo

Hi,

Does anyone know who I should talk to about getting permission and the files for putting the mastercraft logo on some of our club apparel?

Thx,

Paul
Forum: General Discussion 01-03-2014, 03:15 PM
Replies: 2
Views: 200
Posted By KWSC
i blow our heater core out with compressed air. ...

i blow our heater core out with compressed air. disconnect the hose feeding it and stick a air gun down it. I've done this without incident for 10 years (knock on wood!)
Forum: Upholstery 11-15-2013, 11:27 AM
Replies: 14
Views: 841
Posted By KWSC
thanks everyone. I agree, even if the fix did...

thanks everyone. I agree, even if the fix did work, the seat is 11 years old and the vinyl isn't as supple as it once was and so getting new vinyl will probably be cheaper in the long run.

I will...
Forum: Upholstery 11-14-2013, 11:03 PM
Replies: 14
Views: 841
Posted By KWSC
Here's a picture of the split

any thoughts on this??
Forum: Upholstery 11-14-2013, 03:15 PM
Replies: 14
Views: 841
Posted By KWSC
split drivers seat vinyl

Hi - any recommendations on what I should do to repair my drivers seat vinyl that has a split in it (the removeable seat pad - not the Bolster). Buy a skin, have a upolstery shop custom make? Other...
Forum: General Discussion 11-04-2013, 11:00 AM
Replies: 3,157
Views: 391,003
Posted By KWSC
not a security camera per say - just a webcam...

not a security camera per say - just a webcam that uploads every 1/2hr so we don't make the 15min drive to the site for nothing!
Forum: General Discussion 11-03-2013, 11:35 AM
Replies: 3,157
Views: 391,003
Posted By KWSC
Here's the latest capture from site

calm but not quite as nice (that's snow coming down!)
Forum: General Discussion 11-02-2013, 10:56 PM
Replies: 3,157
Views: 391,003
Posted By KWSC
Our site

55m guides and end gates are visible if you look closely
Forum: Engine / Drive Train 10-18-2013, 06:08 PM
Replies: 12
Views: 655
Posted By KWSC
Fixed - replaced the oil pressure sender (didn't...

Fixed - replaced the oil pressure sender (didn't see the other oil pressure switch). Oil was 40psi at idle cold, 60psi warm while skiing and 20-25psi warm idling. No more alarms!
Forum: Engine / Drive Train 10-15-2013, 01:24 PM
Replies: 12
Views: 655
Posted By KWSC
my gauge pressures are approx: cold idle...

my gauge pressures are approx: cold idle 30-40psi, at speed 40-60psi, fully up to temp idle 1-3psi. Oil is 30hrs old 15w-40.

Looking online for low oil pressure at idle alarms points me to the...
Forum: Engine / Drive Train 10-14-2013, 09:46 PM
Replies: 12
Views: 655
Posted By KWSC
So I was on the water on Saturday and it was...

So I was on the water on Saturday and it was alarming again - really seems like its the oil pressure. Is the oil pump probably to go (and only at idle)? Or is it most likely the sensors? How do I...
Forum: Engine / Drive Train 10-11-2013, 12:26 PM
Replies: 12
Views: 655
Posted By KWSC
The oil pressure is quite low while idling (when...

The oil pressure is quite low while idling (when warm). When the boat is at speed the pressure is right up. Oil level is good. I'll see if I can get a gauge and I will try reving the boat when the...
Forum: Engine / Drive Train 10-11-2013, 11:01 AM
Replies: 12
Views: 655
Posted By KWSC
Anybody have any more ideas other than voltage. ...

Anybody have any more ideas other than voltage. Can this alarm be read?
Forum: Engine / Drive Train 10-09-2013, 03:40 PM
Replies: 5
Views: 806
Posted By KWSC
I've never done it but it seems to me you should...

I've never done it but it seems to me you should be able to take a straight edge off the largest pulley and measure the distance with calipers to the quadrant of each pulley. Dimensions to each...
Forum: Engine / Drive Train 10-09-2013, 03:22 PM
Replies: 12
Views: 655
Posted By KWSC
I have a totally stock battery/alternator setup. ...

I have a totally stock battery/alternator setup. The battery is older so that could be a reason although it has never given us grief - starts up everytime. I would also expect to get this alarm...
Forum: Engine / Drive Train 10-09-2013, 01:26 PM
Replies: 12
Views: 655
Posted By KWSC
alarm while idling

hi,

Recently I have been getting an alarm after extended idling or trolling - say over 1min. The alarm sounds but the check engine light doesn't come on (the light does work). Does anyone know...
Forum: Engine / Drive Train 09-29-2013, 03:52 PM
Replies: 407
Views: 69,222
Posted By KWSC
Nope - I mean the line between the pump and the...

Nope - I mean the line between the pump and the regulator. I assume that it gets brittle over time and thus the reason why I had to use snips to cut the line on both ends.
Forum: Engine / Drive Train 09-29-2013, 12:34 AM
Replies: 407
Views: 69,222
Posted By KWSC
Tested out my fuel pump replacement and so far so...

Tested out my fuel pump replacement and so far so good. Here are my notes from the job:

- lots of gas - bucket is a necessity
- our gas line was rock hard - not crimped but impossible to get off...
Forum: Engine / Drive Train 09-21-2013, 11:47 PM
Replies: 407
Views: 69,222
Posted By KWSC
I can't get the old black hose off the old pump -...

I can't get the old black hose off the old pump - any tips from the pro's besides cutting it?
Forum: Underwater Running Gear 08-21-2013, 11:49 PM
Replies: 2
Views: 571
Posted By KWSC
So my replacement prop is a 14X18. We had to up...

So my replacement prop is a 14X18. We had to up the Perfect Pass by 330rpm to get the same speed over our old. ACME is recommending a 907 - 13.5X19 cup to match the 14X20. Any thoughts?
Forum: Underwater Running Gear 08-12-2013, 11:35 PM
Replies: 2
Views: 571
Posted By KWSC
2002 MC PS 190 Powerslot

Hi,

I have a 2002 PS 190 with the 310HP with a powerslot transmission. The prop on it has been damaged. Its a Cutter 14X20? 4 blade. I put the question mark because on one side it reads 14X20 and...
Showing results 1 to 21 of 21

 

All times are GMT -4. The time now is 11:54 AM.