Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 43
Search took 0.29 seconds.
Search: Posts Made By: spievy79
Forum: Engine / Drive Train 09-11-2014, 09:32 PM
Replies: 14
Views: 531
Posted By spievy79
Ok, I appreciate it. That seemed to more sense...

Ok, I appreciate it. That seemed to more sense than the commander swap to me. I knew the indmars and pcm's were fairly similar, plus I gain an extra BW out of it to boot.
Forum: Engine / Drive Train 09-11-2014, 01:02 PM
Replies: 14
Views: 531
Posted By spievy79
I came across an 87 PCM with 417 hours mated with...

I came across an 87 PCM with 417 hours mated with a 1:1 velvet drive. The boat itself was rotted out (supra ts6m). The motor is complete and he sent me a video of it running prior to pulling it. ...
Forum: Engine / Drive Train 09-07-2014, 11:05 AM
Replies: 14
Views: 531
Posted By spievy79
That makes sense to do it that way.

That makes sense to do it that way.
Forum: Engine / Drive Train 09-06-2014, 09:32 PM
Replies: 14
Views: 531
Posted By spievy79
If it were by chance a RH motor could I get a new...

If it were by chance a RH motor could I get a new tranny to reverse it to LH? He had said it was from a nautique and from what I've read some of their earlier motors were in fact RH, rather than a...
Forum: Engine / Drive Train 09-06-2014, 09:03 PM
Replies: 14
Views: 531
Posted By spievy79
I believe that it will,it's a velvet drive, sadly...

I believe that it will,it's a velvet drive, sadly I don't know the gear ratio off hand
Forum: Engine / Drive Train 09-06-2014, 08:11 PM
Replies: 14
Views: 531
Posted By spievy79
Sorry I cant upload a picture, if I had to guess...

Sorry I cant upload a picture, if I had to guess it looks like it can from an early 80's nautique so I'm not sure if its a LH or RH at this point.
Forum: Engine / Drive Train 09-06-2014, 07:45 PM
Replies: 14
Views: 531
Posted By spievy79
Replacing an Indmar 351 with a commander?

Long story short, I have a cracked block on my indmar 351. I was planning to go with a new block from rapido. However,a guy I know has a friend with a complete from top to bottom commander 351...
Forum: Engine / Drive Train 08-17-2014, 12:44 PM
Replies: 30
Views: 1,529
Posted By spievy79
Ok, I'll give that a try. Thanks again.

Ok, I'll give that a try. Thanks again.
Forum: Engine / Drive Train 08-17-2014, 11:15 AM
Replies: 30
Views: 1,529
Posted By spievy79
The reason for the dash is its age and corrosion...

The reason for the dash is its age and corrosion in the wires is all. Also, the timing has not been changed since the last time I ran it
Forum: Engine / Drive Train 08-17-2014, 11:13 AM
Replies: 30
Views: 1,529
Posted By spievy79
Can you elaborate on the posts to the solenoid? I...

Can you elaborate on the posts to the solenoid? I have four posts occupied. On top is the positive to the battery, on the side is a smaller gauge with two wires connected to it, then another small...
Forum: Engine / Drive Train 08-17-2014, 09:34 AM
Replies: 30
Views: 1,529
Posted By spievy79
I planned to get a new long block from rapido...

I planned to get a new long block from rapido marine as mentioned. They seem to have a good track record from what I've read.
Forum: Engine / Drive Train 08-17-2014, 09:32 AM
Replies: 30
Views: 1,529
Posted By spievy79
I was able to get it to fire a few times but it...

I was able to get it to fire a few times but it kept wanting to die. Now it will barely crank over at all. I cleaned off my ground, swapped all my cables to new and still the same thing. I've...
Forum: Engine / Drive Train 08-12-2014, 10:22 PM
Replies: 30
Views: 1,529
Posted By spievy79
The weld is actually holding thus far. I'm...

The weld is actually holding thus far. I'm struggling with it cranking over slowly after putting it all back together, after having water in the oil from a bad head gasket.
Forum: Engine / Drive Train 08-12-2014, 09:31 PM
Replies: 30
Views: 1,529
Posted By spievy79
Well, got everything back together and...

Well, got everything back together and surprisingly the weld held. I pulled off the intake to check it after getting milky oil. Turns out of the head gaskets was leaking at a water jacket. I...
Forum: Engine / Drive Train 08-06-2014, 01:31 PM
Replies: 30
Views: 1,529
Posted By spievy79
The crack is internal, its about 2" long along...

The crack is internal, its about 2" long along the water jacket.
Forum: Engine / Drive Train 08-05-2014, 03:35 PM
Replies: 30
Views: 1,529
Posted By spievy79
We attempted to with a torch but we do not know...

We attempted to with a torch but we do not know what temp we got it up to. After reading some lit on welding iron it is pretty clear we didn't do it correctly, my main question is: running it and if...
Forum: Engine / Drive Train 08-05-2014, 03:09 PM
Replies: 30
Views: 1,529
Posted By spievy79
Ha ha, will do!

Ha ha, will do!
Forum: Engine / Drive Train 08-05-2014, 01:48 PM
Replies: 30
Views: 1,529
Posted By spievy79
And on a side note the crack was so corroded when...

And on a side note the crack was so corroded when we discovered it, it appears it may have been that way for a while. I never found a trace of water in the oil either when emptying it. The PO...
Forum: Engine / Drive Train 08-05-2014, 01:38 PM
Replies: 30
Views: 1,529
Posted By spievy79
We ended up making a channel and welding it at my...

We ended up making a channel and welding it at my buddy's machine shop. No damage to the cylinders it appears. I'll run it and seehow long it lasts. I figure I'm in the same boat either way needing...
Forum: Engine / Drive Train 08-03-2014, 12:19 PM
Replies: 30
Views: 1,529
Posted By spievy79
Are they a reputable company in your opinion?

Are they a reputable company in your opinion?
Forum: Engine / Drive Train 08-03-2014, 11:43 AM
Replies: 30
Views: 1,529
Posted By spievy79
cracked block, looking for best suggestions

Upon my top end rebuild I found a 2" crack at the water jacket. Curious what options I've got here. I already spent about $900 on new heads, intake, gaskets etc. prior to finding this. Wondering what...
Forum: Engine / Drive Train 07-19-2014, 05:50 PM
Replies: 14
Views: 564
Posted By spievy79
The plot thickens.....I bought the edelbrock...

The plot thickens.....I bought the edelbrock performer intake BTW. Thank you to everyone for all the help. Anyway, I took the stock heads in to have them pressure tested and resurfaced and it turns...
Forum: Engine / Drive Train 07-16-2014, 01:36 PM
Replies: 14
Views: 564
Posted By spievy79
Good deal, thanks for the quick reply!

Good deal, thanks for the quick reply!
Forum: Engine / Drive Train 07-16-2014, 01:19 PM
Replies: 14
Views: 564
Posted By spievy79
Ok, thank you. Will these suggestions all bolt...

Ok, thank you. Will these suggestions all bolt up without any modifications? I have read in some other threads that in some circumstances I might need a new flame arrestor, can anyone attest to that...
Forum: Engine / Drive Train 07-16-2014, 10:40 AM
Replies: 14
Views: 564
Posted By spievy79
Advice on buying an intake for 351W

Had a chunk of my intake let loose and landed on two of my pistons last weekend. We pulled the heads off and found the hole in the intake. The pieces had welded themselves to the pistons. Which...
Showing results 1 to 25 of 43

 

All times are GMT -4. The time now is 04:02 AM.