Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 74
Search took 0.73 seconds.
Search: Posts Made By: sjbrothers
Forum: Electrical Yesterday, 07:45 PM
Replies: 0
Views: 42
Posted By sjbrothers
Perfect pass constant

I am stuck. My 2008 X14 is stuck on running 20 mph without perfect pass being activated. I have looked at everything on the dash side and i even have the problem with the VDIG unplugged. Is it the...
Forum: Electrical 08-14-2018, 11:28 AM
Replies: 18
Views: 4,177
Posted By sjbrothers
This post fixed my problem too.

This post fixed my problem too.
Forum: For Sale: Parts & Accessories 08-19-2016, 07:34 AM
Replies: 6
Views: 2,339
Posted By sjbrothers
This is the same light my dealer says is...

This is the same light my dealer says is recommended/sold as a replacement for my 2008 LED light which I crushed when putting my boat on the lift. Bad news not LED. good news not as tall as the...
Forum: Electrical 08-10-2016, 03:48 PM
Replies: 15
Views: 1,965
Posted By sjbrothers
Get a battery tester that will load the battery....

Get a battery tester that will load the battery. It has a switch that puts a load on your battery and if it is soft the voltage will drop. I have one from Carquest and it will tell you if you have a...
Forum: General Discussion 08-10-2016, 03:39 PM
Replies: 12
Views: 955
Posted By sjbrothers
I replaced mine last year because two buttons...

I replaced mine last year because two buttons would not make contact. Tried a work around to keep from buying new but it didn't work. I am keeping the old one hoping to get a button pad someday.
Forum: Electrical 08-03-2016, 07:32 AM
Replies: 38
Views: 2,054
Posted By sjbrothers
Where are you in France? I am coming to Nice at...

Where are you in France? I am coming to Nice at the end of September and I can help you turn the ignition switch. That's a joke as I hope you are skiing by then.
Forum: Engine / Drive Train 07-29-2016, 05:05 PM
Replies: 14
Views: 1,327
Posted By sjbrothers
I asked this thread to be reopened so I could...

I asked this thread to be reopened so I could fall on my sword and tell anyone with this problem to check the battery under load. my 'fix' lasted a couple of pulls but then started again. yesterday...
Forum: Storage / Winterization 07-15-2016, 07:38 PM
Replies: 7
Views: 1,827
Posted By sjbrothers
See my post. The software will not work with...

See my post. The software will not work with anything but MasterCraft. So I am told. BTW my replacement has the copper spring in it and it is to close the flap to keep the water out if you have to...
Forum: Engine / Drive Train 07-15-2016, 07:34 PM
Replies: 14
Views: 1,327
Posted By sjbrothers
I want to close this thread out. The problem was...

I want to close this thread out. The problem was the Airmar Triducer. Good news was that MasterCraft still has the part. Bad news is the price. I talked to Airmar and MasterCraft and they said the...
Forum: Storage / Winterization 07-13-2016, 07:39 AM
Replies: 7
Views: 1,827
Posted By sjbrothers
Good news bad news

I talked to service folks at Airmar and MasterCraft and unfortunately we will have to buy this part from MasterCraft and it is $550.39 from my dealer. The unit is the same with several suppliers like...
Forum: Engine / Drive Train 07-12-2016, 12:40 PM
Replies: 14
Views: 1,327
Posted By sjbrothers
Airmar web site has a lot of information and...

Airmar web site has a lot of information and cross references many of the uses for the same Triducer and I talked to their service people and since this part uses the CAN interface all the hardware...
Forum: Storage / Winterization 07-12-2016, 07:51 AM
Replies: 7
Views: 1,827
Posted By sjbrothers
Having the same problem with the same part. Try...

Having the same problem with the same part. Try just unplugging it. I use an app on my iPhone for speed and rpm mode on the perfect pass with the AirMac unplugged.
Forum: Engine / Drive Train 07-12-2016, 07:47 AM
Replies: 14
Views: 1,327
Posted By sjbrothers
Anyone have a schematic or info on the Airmar...

Anyone have a schematic or info on the Airmar Triducer? I think the tri means depth, water temp and speed. Right?
Forum: Engine / Drive Train 07-11-2016, 08:20 AM
Replies: 14
Views: 1,327
Posted By sjbrothers
Which of the 5 wires needs a diode? I know when I...

Which of the 5 wires needs a diode? I know when I remove the red wire the problem disappears but I think that is the power.
Forum: Engine / Drive Train 07-10-2016, 09:09 PM
Replies: 14
Views: 1,327
Posted By sjbrothers
Well this problem turned out to be caused or...

Well this problem turned out to be caused or effected by the Airmar Triducer. When I unplug it the rpm drops to a normal 650-700 and the speedometer returns to zero. I had read an earlier post where...
Forum: Ballast 07-03-2016, 04:48 PM
Replies: 25
Views: 5,754
Posted By sjbrothers
I would try measuring the voltage at the pump and...

I would try measuring the voltage at the pump and move back to the switch. I would think the pump not showing on the screen would not be the source of the problem but more likely a result of the...
Forum: Engine / Drive Train 06-18-2016, 02:44 PM
Replies: 14
Views: 1,327
Posted By sjbrothers
Thanks, my next step is to make a cable interface...

Thanks, my next step is to make a cable interface so I can measure it while connected to the throttle. Which drop box would have the specs?
Forum: Engine / Drive Train 06-18-2016, 08:01 AM
Replies: 14
Views: 1,327
Posted By sjbrothers
Voltage on TPS at idle

I am chasing a problem on my 2008 X14 with high idle of 1000 rpm after starting. I have removed the throttle position sensor and put it on the bench and applied 5 volts and measured the voltage on...
Forum: Electrical 10-16-2015, 04:24 PM
Replies: 46
Views: 9,361
Posted By sjbrothers
I just received my voltage converter yesterday so...

I just received my voltage converter yesterday so getting ready to do some testing to see if it will give me what I want. I am looking for filtering and a slight increase in supply voltage to the...
Forum: Electrical 10-06-2015, 10:43 AM
Replies: 46
Views: 9,361
Posted By sjbrothers
Thanks I'll give it a look. The sun has finally...

Thanks I'll give it a look. The sun has finally come out in North Carolina ��
Forum: Electrical 10-05-2015, 10:53 AM
Replies: 12
Views: 2,454
Posted By sjbrothers
The new sensor did work but only after I cut two...

The new sensor did work but only after I cut two inches off the 9 inch long tube. Seems odd that the dealer nor MasterCraft would know/tell you that was required. Next I guess I will have to see how...
Forum: Electrical 10-04-2015, 02:12 PM
Replies: 46
Views: 9,361
Posted By sjbrothers
Time for a redesign

I am going to try adding a dc to dc converter to increase the voltage to the mdc. I am also having a problem when I turn on the ballast pumps all the gauges go to zero until the voltage dip recovers....
Forum: Electrical 10-01-2015, 04:22 PM
Replies: 46
Views: 9,361
Posted By sjbrothers
Where are they located? Under dash or back of the...

Where are they located? Under dash or back of the engine? Seems strange to have two fuses in series to the mdc?
Forum: Electrical 09-30-2015, 06:37 PM
Replies: 46
Views: 9,361
Posted By sjbrothers
Well today the gauges worked. I measured the...

Well today the gauges worked. I measured the voltage drop from the battery to the voltage buss under the dash and it was .125 volts and when I turned on the ignition the voltage at the dash buss to...
Forum: Electrical 09-30-2015, 10:31 AM
Replies: 46
Views: 9,361
Posted By sjbrothers
Chasing the same problem with gauges. The fuel...

Chasing the same problem with gauges. The fuel gauge float was not working so I ordered a new one and it was a different design with no float but the gauge still doesn't work. Also all the gauges go...
Showing results 1 to 25 of 74

 

All times are GMT -4. The time now is 04:04 AM.


2018