Go Back   TeamTalk > Search Forums

Showing results 1 to 16 of 16
Search took 0.00 seconds.
Search: Posts Made By: jtank
Forum: General Discussion 08-09-2010, 01:36 PM
Replies: 9
Views: 4,881
Posted By jtank
I have a 2007 197 280 hours LY6 loaded.

I have a 2007 197 280 hours LY6 loaded.
Forum: Engine / Drive Train 09-18-2007, 09:45 PM
Replies: 12
Views: 1,960
Posted By jtank
I just ran it tonight before I put the OJ 4 blade...

I just ran it tonight before I put the OJ 4 blade on:
30mph@3490
34.2mph@3810
36mph@4040
Forum: Engine / Drive Train 09-18-2007, 08:46 PM
Replies: 12
Views: 1,960
Posted By jtank
I was wrong, I also checked and it shows 1.22:1. ...

I was wrong, I also checked and it shows 1.22:1. I run 3490 RPM's at 30 MPH with the 13X12 OJ.
Forum: Engine / Drive Train 09-18-2007, 05:01 PM
Replies: 12
Views: 1,960
Posted By jtank
Yes, it is a 1.26:1. OJ claims they are running...

Yes, it is a 1.26:1. OJ claims they are running a 13.7x 15 4 blade on all LY6 TT boats.
Forum: Engine / Drive Train 09-18-2007, 03:28 PM
Replies: 12
Views: 1,960
Posted By jtank
The owners manual does not give all the details...

The owners manual does not give all the details as my LY6 is running a OJ 13X12.
Forum: Engine / Drive Train 09-18-2007, 03:06 PM
Replies: 12
Views: 1,960
Posted By jtank
Prop Used On the 197 LY6 TT

What prop is being used on the 07 197 LY6 TT ? I know it is a OJ but not sure if it is a 3 or 4 blade and size.
Forum: General Discussion 04-20-2007, 02:54 PM
Replies: 2
Views: 558
Posted By jtank
Zero Off

Has anybody had any luck trying to purchase this product ?
Forum: General Discussion 07-06-2005, 04:28 PM
Replies: 38
Views: 2,160
Posted By jtank
I'am happy to report that MC is going to over...

I'am happy to report that MC is going to over night the ECM so it is here tomorrow. I will give an update tomorrow night on the status.
Forum: General Discussion 07-05-2005, 06:07 PM
Replies: 38
Views: 2,160
Posted By jtank
I called to check on the boat and they told me...

I called to check on the boat and they told me the ECM board will not allow the computer to talk to it. Why this happened they do not know ! All they can tell me is that it the part is a $1000.00...
Forum: General Discussion 07-05-2005, 01:57 PM
Replies: 38
Views: 2,160
Posted By jtank
Jim, Thanks for your help in trying to get me...

Jim,

Thanks for your help in trying to get me out of a bind this past weekend. However, I disagree with your statement that," nobody makes a boat the is ready to go at the time of delivery". I...
Forum: General Discussion 07-04-2005, 10:35 PM
Replies: 38
Views: 2,160
Posted By jtank
Thanks, I tried it all and it still shows "ECM" ?...

Thanks, I tried it all and it still shows "ECM" ? I did get a hold of a tech in Seattle and he said that they will need to hookup the computer to it. Again, disapointed in MC as there are alot of...
Forum: General Discussion 07-03-2005, 11:43 PM
Replies: 38
Views: 2,160
Posted By jtank
Thanks, I looked and all three fuzes are good. ...

Thanks, I looked and all three fuzes are good. The Craft let me down and out ! Very disapointed in the 05 197 so far ! It has been in the shop four times already for similar issues.
Forum: General Discussion 07-03-2005, 01:26 PM
Replies: 38
Views: 2,160
Posted By jtank
The engine will turn over, and I have tried a...

The engine will turn over, and I have tried a reset. When you say pop the cap, are they located inside the plastic deals that snap into the back panel behind the engine (MCX).
Forum: General Discussion 07-03-2005, 01:05 PM
Replies: 38
Views: 2,160
Posted By jtank
Didn't work, it still shows ECU!!!!!!!!!!

Didn't work, it still shows ECU!!!!!!!!!!
Forum: General Discussion 07-03-2005, 11:37 AM
Replies: 38
Views: 2,160
Posted By jtank
Is it possible to by pass it ?

Is it possible to by pass it ?
Forum: General Discussion 07-03-2005, 11:11 AM
Replies: 38
Views: 2,160
Posted By jtank
Angry 2005 197 Won't Start

It ran for 3 minutes then shut off. It gave an error message on the LCD of "ECM". Also, none of the gauges work, but the blower and radio work etc. I have check all electrical conections and...
Showing results 1 to 16 of 16

 

All times are GMT -4. The time now is 09:47 PM.