Go Back   TeamTalk > Search Forums

Showing results 1 to 16 of 16
Search took 0.00 seconds.
Search: Posts Made By: spievy79
Forum: Engine / Drive Train 03-26-2014, 11:29 PM
Replies: 2
Views: 119
Posted By spievy79
Pertronix Ignitor vs. Ignitor II on 351

I am upgrading points to EI and wondered what people's thoughts were regarding the regular ignitor versus the Ignitor II. Will I need to get different spark plug wires with the Ignitor II? I just...
Forum: Engine / Drive Train 03-24-2014, 11:35 PM
Replies: 5
Views: 330
Posted By spievy79
Thanks guys, I ended up just replacing all the...

Thanks guys, I ended up just replacing all the wires....ground,battery to solenoid,solenoid to starter, and all is well. I thought I destroyed some things with my wiring but turns out I did it right...
Forum: Engine / Drive Train 03-24-2014, 04:05 PM
Replies: 5
Views: 330
Posted By spievy79
Would anyone see any harm in just going straight...

Would anyone see any harm in just going straight from the starter to the battery to eliminate the starter being bad?
Forum: Engine / Drive Train 03-24-2014, 03:33 PM
Replies: 5
Views: 330
Posted By spievy79
Negative battery smoking trying to start

I had to rewire my boat's main engine to dash connections because when I removed the engine this fall two of the prongs on my 8 wire connector broke off due to corrosion. I decided to just wire...
Forum: Engine / Drive Train 03-19-2014, 01:41 AM
Replies: 2
Views: 88
Posted By spievy79
Ok. Thank you for the heads up.

Ok. Thank you for the heads up.
Forum: Engine / Drive Train 03-19-2014, 01:29 AM
Replies: 2
Views: 88
Posted By spievy79
Question on adding a water separating filter to 5.8 with filter in fuel pump

Already have a filter in the bottom of the fuel pump. I am thinking of adding a water separating fuel filter before the fuel pump. Thoughts? I don't want to restrict flow by having two filters...
Forum: Engine / Drive Train 03-17-2014, 09:31 PM
Replies: 12
Views: 571
Posted By spievy79
Well I'm back. I was able to get the engine in...

Well I'm back. I was able to get the engine in the right fore and aft position and got the alignment pretty close and bolted her in. I spent a few hours aligning and decided I needed some more...
Forum: Engine / Drive Train 03-11-2014, 10:47 PM
Replies: 12
Views: 571
Posted By spievy79
Yes, thank you both for the information. It all...

Yes, thank you both for the information. It all makes sense and paints a good blueprint. The old marks on the shaft is a great point. I had forgot about that completely....somehow ;). That really...
Forum: Engine / Drive Train 03-10-2014, 11:27 PM
Replies: 12
Views: 571
Posted By spievy79
Frank, sorry I didn't see that first part you...

Frank, sorry I didn't see that first part you mentioned until rereading just now. What roughly should be the prop to rudder clearance? Obviously an inch isn't enough, I just don't remember from my...
Forum: Engine / Drive Train 03-10-2014, 11:21 PM
Replies: 12
Views: 571
Posted By spievy79
I dont have a set of instructions downloaded or...

I dont have a set of instructions downloaded or anything just what I have read in other posts. I appreciate all the info. I replaced the cutless bearings because the old ones were trashed I'm...
Forum: Engine / Drive Train 03-10-2014, 10:14 PM
Replies: 12
Views: 571
Posted By spievy79
Pictures are in albums in my profile but I cant...

Pictures are in albums in my profile but I cant seem to get them to show up by inserting image with the url??
Forum: Engine / Drive Train 03-10-2014, 10:09 PM
Replies: 12
Views: 571
Posted By spievy79
http://www.mastercraft.com/teamtalk/album.php?albu...

http://www.mastercraft.com/teamtalk/album.php?albumid=1020&pictureid=6069
Forum: Engine / Drive Train 03-10-2014, 09:41 PM
Replies: 12
Views: 571
Posted By spievy79
Gotcha. I can get some on here. :)

Gotcha. I can get some on here. :)
Forum: Engine / Drive Train 03-10-2014, 09:25 PM
Replies: 12
Views: 571
Posted By spievy79
Rebuilt stringers and dropped engine back in trying to do alignment

I put the 5.8 back in last night after redoing all the fun stuff.....stringers,floor,carpet etc. When I pulled the motor originally the stringers were obviously junk and the mounts were sunk an inch...
Forum: Engine / Drive Train 09-26-2013, 09:25 PM
Replies: 3
Views: 385
Posted By spievy79
Thanks, I had looked once and didn't find it,...

Thanks, I had looked once and didn't find it, this time around I did.
Forum: Engine / Drive Train 09-26-2013, 05:19 PM
Replies: 3
Views: 385
Posted By spievy79
1987 351W need help finding motor mounts

Hello, A new guy here. I don't own a Mastercraft so I'm hopeful I don't get shunned for that but have an Indmar 351W, 240hp in my 1987 Ski Supreme Cuddy. This is my third inboard so I'm not new to...
Showing results 1 to 16 of 16

 

All times are GMT -4. The time now is 03:47 PM.