Go Back   TeamTalk > Search Forums

Showing results 1 to 25 of 500
Search took 0.07 seconds.
Search: Posts Made By: blackhawk
Forum: Ballast 07-16-2018, 10:17 PM
Replies: 5
Views: 115
Posted By blackhawk
Check to see what voltage you are getting at the...

Check to see what voltage you are getting at the pumps.
Forum: Underwater Running Gear 07-05-2018, 10:27 PM
Replies: 20
Views: 486
Posted By blackhawk
You could take them to a machine shop and have...

You could take them to a machine shop and have them knurl them. They can control the knurl height and build it up to get a tight fit for you.
Forum: General Discussion 07-03-2018, 11:04 PM
Replies: 9
Views: 391
Posted By blackhawk
I was able to carefully tweak my strut back in...

I was able to carefully tweak my strut back in alignment. Just like gwozhog, I used a piece of 1-1/8" round that I found at work. I got the shaft pretty well centered in the thru hull fitting....
Forum: Engine / Drive Train 06-29-2018, 09:02 PM
Replies: 12
Views: 375
Posted By blackhawk
Does it have a waterline running to it? If it...

Does it have a waterline running to it? If it does, it is dripless.
Forum: Engine / Drive Train 06-29-2018, 09:01 PM
Replies: 12
Views: 350
Posted By blackhawk
Do you have a link to that Youtube video?

Do you have a link to that Youtube video?
Forum: General Discussion 06-29-2018, 08:54 PM
Replies: 6
Views: 176
Posted By blackhawk
How many did you need?

How many did you need?
Forum: General Discussion 06-28-2018, 08:38 AM
Replies: 9
Views: 391
Posted By blackhawk
Waterlogged - Thanks for the good info. I...

Waterlogged - Thanks for the good info. I definitely wouldn't move the strut if the shaft wasn't touching the thru hull fitting. I think it would rub a groove in the fitting as it is now and...
Forum: General Discussion 06-26-2018, 11:17 PM
Replies: 9
Views: 391
Posted By blackhawk
Shaft/strut alignment woes - HELP!

Short story: I checked my shaft to engine alignment tonight (2006 X15). I slid off the OJ dripless shaft seal from the thru hole fitting first. When I unbolted the trans coupling and disengaged the...
Forum: General Discussion 06-15-2018, 10:36 PM
Replies: 14
Views: 468
Posted By blackhawk
Try cleaning your battery terminals. Also trace...

Try cleaning your battery terminals. Also trace the negative battery cable back to the engine and clean that connection. Check your grounds under/behind the dash also.

If that doesn't work, just...
Forum: Off Topic Discussion 06-11-2018, 10:39 PM
Replies: 9
Views: 912
Posted By blackhawk
I make cedar signs on the side. I always use...

I make cedar signs on the side. I always use Sikkens Cetol on them. I've never had any complaints or returns. No idea how it would wear on a dock though with foot traffic. My guess would be that...
Forum: Engine / Drive Train 06-06-2018, 09:24 PM
Replies: 11
Views: 361
Posted By blackhawk
NAPA should be able to cross over this: AcDelco...

NAPA should be able to cross over this: AcDelco GM Distributor Cap (D329A) And Rotor (D465)
AC Delco plugs are MR43LTS if you don't have catalytic converter
Forum: Ballast 05-30-2018, 10:18 PM
Replies: 3
Views: 312
Posted By blackhawk
First thing to do is get a multimeter and test if...

First thing to do is get a multimeter and test if you have voltage at the quick disconnect plug next to the pump. You'll need some needle style probes. You should see at least 12 volts when you...
Forum: General Discussion 05-04-2018, 11:21 PM
Replies: 38
Views: 1,891
Posted By blackhawk
I had a 19' Stingray before my MC. I ran it for...

I had a 19' Stingray before my MC. I ran it for 3 seasons with zero problems. I did have to put trim tabs on it though. The Stingrays will porpoise like crazy without them. It was a totally...
Forum: Engine / Drive Train 04-27-2018, 10:19 PM
Replies: 6
Views: 391
Posted By blackhawk
I emailed Indmar and they said the best place to...

I emailed Indmar and they said the best place to inject the oil would be through the oil sending port. Indmar also told me that the oil sending unit used 1/4" NPT threads, but I don't think that is...
Forum: Engine / Drive Train 04-26-2018, 11:28 PM
Replies: 6
Views: 391
Posted By blackhawk
The pre-luber pump pulls oil from the drain plug...

The pre-luber pump pulls oil from the drain plug in the oil pan then pumps it into the oil galley. This pressurizes the oil system and lubricates the engine before it is started, thereby preventing...
Forum: Electrical 04-26-2018, 10:52 PM
Replies: 8
Views: 794
Posted By blackhawk
If worse comes to worse, you might find someone...

If worse comes to worse, you might find someone that could 3D print it for you.
Forum: Engine / Drive Train 04-26-2018, 10:49 PM
Replies: 6
Views: 391
Posted By blackhawk
Where to inject oil into MCX for pre-luber?

I want to hook up an external engine oil pre-luber to my 2006 MCX. Where is the best place to connect a fitting that connects to the oil galley?

I am sure that the port that the oil pressure sender...
Forum: Ballast 04-18-2018, 10:13 PM
Replies: 40
Views: 9,970
Posted By blackhawk
It works! See my picture in post #5 of this...

It works! See my picture in post #5 of this thread. I've been using them every outing for 3 years now. I promise you that 460s will not give you enough weight in the X15 for a good surf wave.
Forum: General Discussion 04-18-2018, 10:06 PM
Replies: 11
Views: 537
Posted By blackhawk
3M adhesive remover is worth a try. Never tried...

3M adhesive remover is worth a try. Never tried it on a swim deck mat, but it has never failed me on anything else.
Forum: Engine / Drive Train 04-11-2018, 10:02 PM
Replies: 10
Views: 890
Posted By blackhawk
Thanks for letting us know the fix. How exactly...

Thanks for letting us know the fix. How exactly was the FAE causing the surge?
Forum: Electrical 04-11-2018, 09:59 PM
Replies: 13
Views: 937
Posted By blackhawk
I would solder the new leads onto the old ones. ...

I would solder the new leads onto the old ones. That is really the right way to do it. This is a really good video on soldering: https://www.youtube.com/watch?v=Zu3TYBs65FM
Forum: Ballast 04-11-2018, 09:47 PM
Replies: 40
Views: 9,970
Posted By blackhawk
Yes, just piggy back on top of the factory tanks....

Yes, just piggy back on top of the factory tanks. Go search Wakemakers.com for info on how to do the piggy back. It is easy.

I would get the Straight Line Sumo 850s for the rear. I have the...
Forum: Engine / Drive Train 03-31-2018, 12:16 PM
Replies: 13
Views: 6,250
Posted By blackhawk
Hello Zeus - You did it correctly the first time....

Hello Zeus - You did it correctly the first time. After you get all the o-rings in place, put the cover in place and push down on top of the cover with your fingers as hard as you can. As you hold...
Forum: Appearance 03-18-2018, 10:40 PM
Replies: 8
Views: 594
Posted By blackhawk
Send Mastercraft an email via their website. ...

Send Mastercraft an email via their website. They answered me back in a day when I had the exact same question.
Forum: General Discussion 03-01-2018, 10:09 PM
Replies: 40
Views: 2,526
Posted By blackhawk
Interstate for me.

Interstate for me.
Showing results 1 to 25 of 500

 

All times are GMT -4. The time now is 05:23 PM.


2018