Go Back   TeamTalk > View Profile

thatsmrmastercraft thatsmrmastercraft is online now

MC Master Poster

Visitor Messages

Showing Visitor Messages 11 to 20 of 22
  1. Slinkyredfoot
    09-18-2013 10:02 AM
    Slinkyredfoot
    Hey Peter, read the news about Jim Baws, I am floored. He helped me a bunch when I was redoing my boat. Do you know what happened??
  2. lil'red
    06-27-2012 05:00 PM
    lil'red
    Hey man, your boat looks great! Looks like you've made some well thought out improvements to the original...

    I recently inherited a 79' S&S with the 351ci. It was the boat I grew up on and learned to tow, launch, wrench etc....

    I hate to say I definitely didn't pay enough attention to old dad when we would start it up before trips and I just can't seem to figure out which port I would want to connect the hose to, to fire this thing up in the drive way.

    I know my dad always just connected the garden hose to it directly at the inlet pump but I don't want to make a costly mistake or even burn up an impeller before I even get to take it out. Can you help?

    Thanks in advance!

    wes

    Here's a shot of what I'm sure you are already familiar with... I scoped it out though and her I have noted what I thought to be the inlet pickup port.

    http://s17.postimage.org/ykfc7zr9b/motor_shot.jpg
  3. Slinkyredfoot
    10-10-2011 07:36 AM
    Slinkyredfoot
    You seem to well versed in fixing stuff so I was wondering if you have any thoughts on my trailer wiring issue. Pulled the boat home yesterday and noticed everytime I put on the brakes or used the turn signal the clearance lights of the side of the trailer would either blink if the trun signal was on or light up when I applied the brakes. Everything worked fine last time I used the trailer and was wondering what might be the problem. If you could shed some light on this I would appreciate it.
    Thanks Peter,
    Steve
  4. americanskierJim
    07-27-2011 06:11 PM
    americanskierJim
    Just passin by Peter to say HI. Hope you are having a great Summer. I have been having a wonderful summer with the boys skiing and tubing. I have been up a couple times on the ski. Keep inouch. Jim
  5. oxberger
    06-10-2011 05:02 PM
    oxberger
    I'm trying to start a thread and can't seem to figure it out. I don't have a new thread button anywhere and it shows I have the permision to start one. Any clue on how I can do it?
  6. Skir68
    05-11-2011 09:05 AM
    Skir68
    Good Morning! I see you are a M/C owner and are on Team Talk alot
    My wife and I just purchased a prostar 190 and Live in Buffalo
    We would like to get to know other M/C owners in the area
    Where does everyone ski?
  7. americanskierJim
    02-16-2011 10:55 PM
    americanskierJim
    Hi Peter, Just thought I would pass by and say HI. Hope your having a great start to the new year.
  8. LaRue
    01-29-2011 11:06 PM
    LaRue
    Thought u might know the answer to a question. What boats have the same hull design as a 2000 maristar, if any, other than the X10? Thanks in advance.
  9. Slinkyredfoot
    01-18-2011 05:28 PM
    Slinkyredfoot
    How ya doing? My name is Steve, live in Carmel Indiana and very long time MasterCraft owner Enjoy your input here and typically read your responses and threads, you seem to be in tune. Did not want to thread jack the fuel injection thread so I thought I would email you for some input.
    I am pretty well versed and mechanically inclined much like you, but the problem I referred to with my engine stalling after use is mind boggling to me. I have done everything, new coil, plug wires, converted to pointless ignition, new fuel filter with water separator, you name it I have done it. The stalling problem started two summers ago and I am at wits end. Like I said, have a good friend who I trust totally, he still says it is ethanol fuel I buy at the gas station which kinda makes sense. Almost like vapor lock or something. Just trying to get thoughts. I think my old oringinal carb may need some attention, but it starts so good and runs so fine I hate to screw around with things. Any other thoughts your may have to address my stalling problem? Thanks and good to meet you.
    Steve
  10. bmack1479
    10-21-2010 07:17 PM
    bmack1479
    did you get a chance to post pics of s&s with outboard thanks butch

About Me

  • About thatsmrmastercraft
    City
    St. Paul
    State
    MN
    Location
    St. Paul, MN
    Gender
    male
    Team MasterCraft Member
    no
    Boat Owned
    1977 Stars & Stripes
    Occupation
    Trailer Accessories
  • Signature
    Package Deal:
    Two Chrome 10 hole wheels with Kenda Loadstar radials.
    Mounted, balanced and delivered.
    With ST205/75R14..........$309
    With ST215/75R14..........$346





    PM or email me for tire, wheel or package pricing.
    CARBURETOR REBUILDING - $199
    Parts, labor and return shipping included


    2 LED 6" BRAKE LIGHTS DELIVERED $32
    tiresplease@gmail.com

    Coming soon.......TrailerEssentials.com

Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: Today 12:56 PM
  • Current Activity: Searching Forums
  • Join Date: 09-20-2008
  • Referrals: 0

Friends

Showing Friends 1 to 10 of 52

All times are GMT -4. The time now is 01:10 PM.