MC Master Poster
- User Lists
Showing Visitor Messages 1 to 10 of 20
05-06-2013 03:06 PMlividHey Jim, I saw a forum yesterday in which you replied about taking a wire straight from the battery to the crank on the ignition switch to test it. I was getting a flashing ECU when I tried to start my boat, I went back yesterday and when I turned the key to on, I got nothing, not even the flashing ECU... So I tried running a wire like you said straight from the battery to the ignition and I got the display gauge back (Still flashing ECU). This is an after market ignition that was installed by the dealer because they got it as a repo. I guess my question is what does it mean to run the wire straight from the battery to the ignition? Is that testing the igniton switch?
07-17-2011 12:36 PMdjobarefooterHello again Jim, Last I contacted you was in 2009. Here I am again with another fuel pump issue. ( We have fixed our voltage issue) Yesterday we ran our 1995 LT-1 Sammy Duvall Craft with no issues and 15 gall. of gas. Pulled 4 slalom runs, put boat on lift.
this morning, took off lift to put gas in for barefoot run , boat started, then died in approx 1 min. or so. Won't restart. Battery ok. No humm or click from fuel pump. Checking the fuses and "boxes"(relays) as we speak. We are going through a pump every other year, and only put less than 50 hours on each year. Any ideas what would cause this? Never have run the boat out of gas, but have run it 1/4 tank. Could this be the problem even though th fuel pump is not in the tank? Anything will help us !! Thank you once again in advance!!
08-14-2010 10:11 AMtazdevilhi jim
you seem very knowledgable with idmar engines i have a rpt1 2006 runs fine the only problem is that three injectors wont open i tested them on the bench they work fine but the computer won t open them i am running on a 30psi pump mercruiser coolfuel gen 11 any idea why 3 injectors won t open there are no mastercraft dealers near thanks
06-12-2010 05:20 PMboydJim,
You have helped me before. Hopefully you can do it again. I bought a new to me 87 supra. PCM. Starter is turning over very slowly. New battery, cable connections, I cleaned all the connections. It is original starter. Boat only has 302 hours on it and it's VERY clean. The last owner had the small battery connections coming from the cables to the battery(trolling motor), they were also melted off and he replaced with replacment connections. So, it's been hot before (battery)
Do you think new starter is next ?
Is rebuilding the starter just as good. Is there anything else to check ?
02-18-2010 05:14 PMJ NORRISJim,
I am planning on hooking the hull on my 2001 prostar 209. I have contacted Houston Master Craft and the drawing I got from them is no help at all. It had no dimensions on it! It looked like they wrote it on a napkin while drinking at the bar. I have a reputable fiberglass company here in Houston call Northwest Fiberglass to do the work. However I need the dimensions for them to be able to do the work. If you can help me in anyway it is much appreciated.
(713)725-5901 if you feel like talking in person about it.
or just reply to J NORRIS on the board.
08-19-2009 10:23 PMfentongJim, you seem to be one of the more knowlegable trouble shooters for electrical issues on this forum. I posted an issue yesterday titled Gauges Problems (yeah I know bad choice of title to get attention). I was hoping you could take a look and reply if you have any thoughts on what the issue might be. Any help would be greatly appreciated.
08-17-2009 02:19 PMEricBJim;
I have a waterpump seal leaking on my 98 w/LT1. From the looks of it, the engine circulation pump is camshaft driven?
What's the best way to replace that seal. Can it be done by removing the front watrepump cover, or do i have to take off the whole pump and reseal that way?
07-06-2009 11:11 PMJimNThat's possible but I would still like you to try running a ground from the splice to the battery negative. As I posted, they had a bulletin for these and that was the fix at the time. If that doesn't fix it, then I would look at a new MDC box. Also, look at the terminals on the plug and if the box opens, look inside- if the speedos have pitot tubes instead of a paddlewheel, water can get inside if you have hard freezes in winter and the tubes aren't cleared out when winterizing.