Go Back   TeamTalk > View Profile


MC Fanatic

Visitor Messages

Showing Visitor Messages 61 to 67 of 67
  1. langedp
    05-24-2009 01:11 PM

    I have a 2007 X-Star with the 8.1L engine. It has the 14.25 x 14 prop on it and I've been seeing a lot of talk about the 14.75 x 15.5 prop for the 8.1L. Can you tell me what differences I'll see and how much the 14.75 x 15.5 is? Thanks.

  2. X-5 Driver
    04-06-2009 12:44 PM
    X-5 Driver
    Got your email. Thanks for the info. That's what I get for trying to save some money. Who knows, maybe I'll sell it back on ebay and may make a few bucks ;-)
  3. 10kLakes
    03-16-2009 03:15 PM

    I have a 2007 Mastercraft X-14 with 310 hp RTP-1 engine. I bent my prop last weekend on a piece of wood debris -- I'm going to have it repaired but I'd also like to buy a new one so I'll have a spare.

    I use the boat about 50% of the time for wakeboarding (~2500 engine rpm), 40% for slalam skiing (~3100 rpm), and just cruising around the remainder (typically 3000-3500 rpm).

    Can you recommend a replacement prop? I don't have any issues I'd like to address (hole shot, top end, etc. are fine), but if there is a prop that could improve fuel economy without a noticeable drop in performance that would be great.

    I'm not sure exactly what prop is on my boat currently. One MC dealer told me it was a 13x11, another told me it was 13x12.


  4. steve mc
    02-09-2009 05:51 PM
    steve mc
    i have a 2005 x-45 with the lq9 motor i was wondering if you have a prop that might work better with this setup then stock

    top speed is good but i would like a stronger pull out of the hole with out killing the top end speed any props that might do that
  5. mrprostar
    10-06-2008 09:49 AM
    I'm looking for a 13X11 for a high altitude application or to rebuild my 13x13. What should I expect as far as cost for these choices and do you think that amount of change (13x13 to 13x11) would make much difference?
  6. OSUspenc99
    07-31-2008 10:46 AM

    my buddy hit something in the river yesterday in my boat. I dont know if it is repairable or not. If i Send you a picture can you tell or do I need to send you the prop. It is 13x13LH and I think it is a stainless steel prop

    If you want to call me that would be fine also 419.279.9968 Spencer

  7. jwroblew
    05-28-2008 10:35 AM
    I have a 2003 MC X7 with the original OJ 14x20 prop, the boat has the 310 hp Predator, with a 1.5:1 trans. I use the boat 99% for slalom skiing, the lake I use has a short set up into the course, and at 36mph the boat is up to speed just before the gates. Is there a prop you could recommend for better hole shot so I can get up to speed quicker? Also if it is possible I don't want to be turning tons more RPMs, I'm not worried about top end, but fuel consumption, a little more RPMs would be OK.

About Me

  • About EJ OJPROP
    East Tennessee
    Team MasterCraft Member
    Propeller Monkey
  • Signature
    Eric Johnson
    Johnson Propeller Co., Inc


Total Posts
Visitor Messages
General Information
  • Last Activity: 10-14-2016 09:49 AM
  • Join Date: 03-11-2005
  • Referrals: 1


Showing Friends 1 to 10 of 10

All times are GMT -4. The time now is 12:51 AM.