Go Back   TeamTalk > Social Groups

Social Group
This is a public group.

Team MasterCraft

Group Created by TMCNo1

The Exclusive Club For Mastercraft Boat Owners

View All Members Showing 10 of 235 Member(s)
Showing 5 of 28 Picture(s)
Showing Social Group Messages 1 to 10 of 24
  1. Nbergmann
    08-14-2016 01:58 AM
    Nbergmann
    I have a 2015 mastercraft x30. I have peen playing around with my setup but just can't make a good clean crisp wake. What setups are good? Ballasts, gen 2 surf tabs, speed, rope length, ect.?
  2. restadca
    07-12-2016 12:43 PM
    restadca
    The new guy here. I have a 2007 X30 with 180 hours on it. We had some nasty weather the past could days in West Central MN. I started my boat the other day and while I was driving it, steam started coming from the engine, so I shut the boat off ASAP! The temperature gauge was fine; however, the 90 degree threaded pieces going into the exhaust manifold stripped and blew out. I checked the impeller and it is fine. I replaced the two 90 degree pieces that thread into the exhaust manifold on each side and fired up the boat. After a few minutes, the manifold gets too hot to touch. I took the 1" hose off the 90 to see if there was a steady stream of water and it just spit water on occasion. I'm going to check the hoses going from the impeller to the exhaust manifold, but any thoughts on what to check next? I really don't want to take the boat in if I don't have to b/c I'm going to get charged an arm and a leg, but I don't want to cut a corner either. Any help would be much appreciated!!1
  3. mikemali
    07-07-2016 05:26 PM
    mikemali
    Hello everyone! New Mastercraft owner in Lake Hopatcong, NJ here! I'm excited to join this group.

    I have a 2000 Maristar 210 vrs with a speedo issue. The plastic fitting broke off at the driver's panel and I'm finding it impossible to replace it. I've checked HD, hardware stores, boat dealers and car parts store. It's smaller than 1/8 threaded pipe. If anyone has a lead I'd I would appreciate the help. I'm going to post a photo shortly. Thanks for the help.
  4. Georgiamills
    01-07-2015 09:57 AM
    Georgiamills
    Hello everybody! If anyone is looking for new flooring for their boat this year check out our website @ http://www.commercialmatsandrubber.c...oring-c84.html. We are an online dealer located in upstate NY offering multiple types of marine flooring pre-cut to fit your boat. You can also add your boat manufacturers logo, your boat name or your own design!
  5. ChristopherLerario
    09-21-2014 08:59 PM
    ChristopherLerario
    Hi all....Long time reader first time member....I have a 1988 Tristar had broken teeth on the flywheel earlier this summer and put a new ring gear, clutch plate, and starter on with my diesel mechanic buddy..boat worked like a dream for 4-5 outings and now it only starts in gear. If I go reverse boat dies (no grinding at all), if I put throttle down nothing happens.. Any thoughts? Thanks!
  6. Gmoney
    07-02-2014 09:53 PM
    Gmoney
    Hello, I am new to boating. I recently bought a 1996 mastercraft pro star 190. I took it out the other day for the first time since I bought it and I noticed the boat was taking on water below the motor where the bilge pump is. We did do a lot of sking and tubing but I don't think there should of been that much water, approximately 2 gallons. I was told by another boater that it could be the bellows. Where can I find the bellows and are they hard to replace? Any help would be greatly appreciated.
  7. Derekbranch
    06-26-2014 09:28 PM
    Derekbranch
    I am about 120 pounds 5"5" and still growing i am looking for a new wake board but don't want to invest to much money any suggestions on a board for wake boarding behind a prostar 205v, and also I'm an intermediate rider.
  8. Derekbranch
    06-26-2014 09:23 PM
    Derekbranch
    Hey guys I'm brand new to this site and to boating with a mastercraft I just bought a 2001 prostar 205v and I'm looking to completely redo the interior does anybody have any pictures I can show the guy of similar interiors?
  9. Dalec72
    05-28-2014 09:09 PM
    Dalec72
    I have a 2006 X2 and like a dumb dumb I crossed the acc wires. Hooked up positive to negative and vs. engines runs perfect pass works gauges worked. Replaced the 60 amp acc fuse that blew and a 1 stereo fuse. Now my gauges don't work no bilge no blower ect. All breakers are reset. Any suggestions?
  10. spats0706
    04-10-2014 03:02 PM
    spats0706
    I am a petite 5'3" female, 120lbs looking at purchasing a wakesurf board. My boat is a 95 Prostar with no ballasts, so the wake would be small. Does anyone have suggestions on what board I need. I love the Inland boards but they are so $$$ unless you have a hookup. Any suggestions would be appreciated. I've slalom skied competitively and wake-boarded for 15+ years.

All times are GMT -4. The time now is 04:34 AM.