PDA

View Full Version : 1997 Mastercraft PS190 single axle trailer non skid pad


wtrskick
10-13-2013, 01:45 PM
Im looking for the non skid pads for my ps 190 trailer help much appreciated

mikeg205
10-13-2013, 01:51 PM
cut with logo? or just the tape.

wtrskick
10-13-2013, 03:28 PM
cut with logo

mikeg205
10-13-2013, 03:32 PM
Are you looking for these?

1redTA
10-13-2013, 03:49 PM
http://img.tapatalk.com/d/13/10/14/6ahe9a2y.jpghc

1redTA
10-13-2013, 03:50 PM
I made mine with skate board grip tape and by tracing the MC of the side of my boat

mikeg205
10-13-2013, 03:57 PM
Just sent a request to sea deck - I wonder what they would charge for a set...

Cloaked
10-13-2013, 05:08 PM
Just sent a request to sea deck - I wonder what they would charge for a set...
Another thread here of recent said he bought a sheet ?"x?" for $80 bucks and did the cut-outs himself.

mikeg205
10-13-2013, 08:36 PM
Another thread here of recent said he bought a sheet ?"x?" for $80 bucks and did the cut-outs himself.

I remember that thread - could not find it

MikeyOrange88
10-13-2013, 09:04 PM
I got the material for mine from www.antisliptapeshop.com (resilient type)
this may be the thread referred to above:
http://www.mastercraft.com/teamtalk/showthread.php?t=42256&page=3

Fairly simple to cut out the MC logo or other designs in the resilient type tape.

TxsRiverRat
10-14-2013, 11:00 AM
I got the material for mine from www.antisliptapeshop.com (resilient type)
this may be the thread referred to above:
http://www.mastercraft.com/teamtalk/showthread.php?t=42256&page=3

Fairly simple to cut out the MC logo or other designs in the resilient type tape.

Nice! Lets see pics of yours?

MikeyOrange88
10-14-2013, 02:18 PM
Post #26 in the linked thread above is what I did. I have a dual axle trailer though, so I made mine long enough to cover the entire fender, 'cause I step on mine, with shoes no less.;)

NWMike
10-30-2013, 06:10 PM
I cut mine out of Sea Deck material. Traced the letters from the side of the boat, cut out a template then traced them onto the rubber decking material. I used an x-acto knife with many new blades to keep the cuts clean and sharp. It dulls quick. I went through about 6 blades. You can make them last longer but once you pull the knife up and start again, can get a jagged edge. I used this stuff on the inside of the fenders as well instead of the carpet and it has worked great. Check the site for their blem materials to see if they have the texture and colors you want. I got a blem roll and I can't tell what they call a blem. More than fine for a trailer. Worth getting their material that already has the adhesive backing. Very strong stuff.

Barefooter92
10-30-2013, 10:53 PM
Just need a reason to boost my post numbers :D

102705102704


I do have the AutoCAD file I created if you like...

Barefooter92
10-30-2013, 10:53 PM
Just need a reason to boost my post numbers :D

102705

102704


I do have the AutoCAD file I created if you like...

BrianM
10-31-2013, 09:39 AM
I just did solid Seadek on mine. Materials were about $70. Seadek will cut a custom set for you in a two tone setup for $150.

Here is a photo of what Seadek can do http://www.mastercraft.com/teamtalk/showpost.php?p=944514&postcount=12

bochnak
10-31-2013, 10:41 AM
I need to replace mine also. As an ex-skateboarder, I think I'll try grip tape. The skate shop owner in town happens to be my cousin.

gsxrjtt
11-03-2013, 06:31 PM
Do you know if the platform is the same for a 1993 as the 96

BrianM
11-03-2013, 07:30 PM
Do you know if the platform is the same for a 1993 as the 96

Fenders should be exactly the same.