PDA

View Full Version : Where can I find Deutsch connectors for bilge?


beatle78
05-28-2007, 10:14 AM
Hi guys,

Does anyone know where I can find Deutsch connectors that plug into the wiring harness for the bilge pump and bilge sensor switch?

I'm moving the pump and switch to the center of my boat.

I'm also looking for other options/opinions on the cleanest way to do this.


Thanks,
beatle78

Farmer Ted
05-28-2007, 10:35 AM
Hi guys,

Does anyone know where I can find Deutsch connectors that plug into the wiring harness for the bilge pump and bilge sensor switch?

I'm moving the pump and switch to the center of my boat.

I'm also looking for other options/opinions on the cleanest way to do this


Thanks,
beatle78


Good luck! In fact if you find out let me know.

I tried a few years back and didn't have much luck so I used solder, shrink wrap, and a but load of electrical tape.

Check this out.....
http://www.deutschipd.com/dtmseries.pdf

Looks like it might be worth a call to 909-765-2250 and ask them where to buy them at. If you have to buy in bulk, let me know and I'll take 8 off your hands.

T

beatle78
05-28-2007, 10:39 AM
will do, I just so happen to work with electrical engineers that may be able to get some samples. I'll ask them tomorrow :)

prostar205 said he found them... see his post here

http://tmcowners.com/teamtalk/showthread.php?t=12657&page=2

In the post where he posted the pic of the bilge pump

Farmer Ted
05-28-2007, 10:44 AM
will do, I just so happen to work with electrical engineers that may be able to get some samples. I'll ask them tomorrow :)

prostar205 said he found them... see his post here

http://tmcowners.com/teamtalk/showthread.php?t=12657&page=2

In the post where he posted the pic of the bilge pump


Sole Distributor.......

http://www.laddinc.com/home.aspx

prostar205
05-28-2007, 11:11 AM
Deutsch connectors can be found at.......

www.battsracing.com then at the middle of the page click on.....

http://www.deutschconnector.com/

They are cheap, fast delivery, very reliable.

We use them at work on alot of applications.

prostar205
05-28-2007, 11:15 AM
Hi guys,

Does anyone know where I can find Deutsch connectors that plug into the wiring harness for the bilge pump and bilge sensor switch?

I'm moving the pump and switch to the center of my boat.

I'm also looking for other options/opinions on the cleanest way to do this.


Thanks,
beatle78


beatle78 -

I used the DT Series with 2 contacts. If you are moving your bilge pump, you will need 2 receptacles and 2 plugs and then make a wiring harness to go between the OEM connections located by the tranny to the new location of the bigle.

Farmer Ted
05-28-2007, 11:17 AM
Deutsch connectors can be found at.......

www.battsracing.com (http://www.battsracing.com) then at the middle of the page click on.....

http://www.deutschconnector.com/

They are cheap, fast delivery, very reliable.

We use them at work on alot of applications.


Thanks 205!

JimN
05-28-2007, 11:18 AM
Try Del City- here's their site:www.delcity.net

I'm pretty sure they sell them. Otherwise, cut the wires, extend them and use heat-N-seal shrink wrap. The glue softens and flows into the wire and out the ends, making it at least as impervious to water and other contaminants as the wire's insulation.

Find out what their minimum quantity is and if necessary, I can break a package up and mail them out, since I live about 1/2 mile from Del City.

beatle78
05-28-2007, 12:48 PM
thanks 205!

beatle78
05-28-2007, 12:51 PM
thanks Jimn